dezzer
Member
 Offline
Posts: 6
|
 |
« on: January 27, 2011, 02:57:44 PM » |
|
hi all, new to the site,im looking for some advice,im looking for drag washers for both the above reels,and also a full set of bearings for both and where they can be got,also does anyone know the dimensions of the bearings for both reels,regards eddie..............
|
|
|
|
|
Logged
|
keep your hand on it !......
|
|
|
spes
Member
Offline
Posts: 103
|
|
« Reply #1 on: January 27, 2011, 07:07:18 PM » |
|
I just recieved a full set of bearings for my lx. I ordered them right form Avet. They were $25 for the set of 6 bearings. Don't know about the drag washer, it was glued in  I saw a post around were Alan re-glued one in. Is that the recommended method in a replacement? Don't know. Don't know what size it is either, sorry. Spes |
|
|
|
|
Logged
|
|
|
|
alantani
admin
Administrator
Member
 Online
Posts: 7847
|
|
« Reply #2 on: January 27, 2011, 07:24:45 PM » |
|
go directly to avet for these. they're great when it comes to customer support. alan
|
|
|
|
|
Logged
|
|
|
|
dezzer
Member
Offline
Posts: 6
|
|
« Reply #3 on: January 28, 2011, 01:19:21 PM » |
|
thanks for the comments lads,i have emailed avet a few times,one email said 25dollars each bearing,i emailed back a couple of times since,and have had no replys,that would make it 130dollars just for bearings,regards,eddie.......
|
|
|
|
|
Logged
|
keep your hand on it !......
|
|
|
alantani
admin
Administrator
Member
Online
Posts: 7847
|
|
« Reply #4 on: January 28, 2011, 01:51:29 PM » |
|
no, avet buys very inexpensive blue seal bearings that are $5 each. i generally will not use them because of quality issues. i ordered 20 bearings from them once. every one of them was bad. drag washers are fine, though. alan
|
|
|
|
« Last Edit: January 28, 2011, 01:52:10 PM by alantani »
|
Logged
|
|
|
|
dezzer
Member
Offline
Posts: 6
|
|
« Reply #5 on: January 28, 2011, 02:44:57 PM » |
|
thanks alan,still no word from avet,can you recomend somewhere else to buy bearings,cant seem to locate anywhere in ireland or england,have looked at bocabearings but i do not have dimensions for bearings only part no,s from avet,is there anywhere to get dimensions,regards,eddie.........
|
|
|
|
|
Logged
|
keep your hand on it !......
|
|
|
alantani
admin
Administrator
Member
Online
Posts: 7847
|
|
« Reply #6 on: January 29, 2011, 12:25:19 AM » |
|
i never wrote down the dimensions anywhere, either. if you can pull the bearing from your reels and measure them, i can match them up and ship them to you. otherwise i would be guessing. alan
|
|
|
|
|
Logged
|
|
|
|
dezzer
Member
Offline
Posts: 6
|
|
« Reply #7 on: January 30, 2011, 06:36:27 AM » |
|
thanks alan,will have a go a the measurments,as avet have not got back to me,regards,eddie.....
|
|
|
|
|
Logged
|
keep your hand on it !......
|
|
|
spes
Member
Offline
Posts: 103
|
|
« Reply #8 on: January 30, 2011, 08:07:36 AM » |
|
As I said, I just purchased my LX bearings right from Avet. They were $25 for the full set.
I have them right here in my hand.
Alan, can these be measured with just a ruler? i.e. How precise does it have to be?
I can get a measuring tool from my dad's shop but it would probably be a week before I can get there to get it.
|
|
|
|
« Last Edit: January 30, 2011, 08:45:06 AM by spes »
|
Logged
|
|
|
|
alantani
admin
Administrator
Member
Online
Posts: 7847
|
|
« Reply #9 on: January 30, 2011, 02:07:29 PM » |
|
match them up to a bearing on this list!
|
|
|
|
|
Logged
|
|
|
|
dezzer
Member
Offline
Posts: 6
|
|
« Reply #10 on: January 30, 2011, 02:14:50 PM » |
|
thanks for all the replys lads,alan cant see any list,eddie...........
|
|
|
|
|
Logged
|
keep your hand on it !......
|
|
|
|
|
Cowbass
Member
Offline
Posts: 49
|
|
« Reply #12 on: January 30, 2011, 07:30:38 PM » |
|
If I were you I'd just call avet!!! There email support is horrible, but I hear there good over the phone. I emailed them a month back looking for rod clamps and the tech couldn't even invoice me for a purchase. Also they don't take paypal. I love there reels but they need to step up there online support and purchasing. Good luck!!!
|
|
|
|
|
Logged
|
SHUT UP AND FISH!!!
|
|
|
dezzer
Member
Offline
Posts: 6
|
|
« Reply #13 on: January 31, 2011, 11:13:20 AM » |
|
thanks lads,had a look at the list alan,my measurments seem just to be 1 mil out,and only out on 1 of the 3 measurments,got an email from avet today,25$ for the set of six bearings not each,and 35$postage to ireland,i might not be measuring the bearings right,regards,eddie...........
|
|
|
|
|
Logged
|
keep your hand on it !......
|
|
|
|
