alan tani @ alantani.com fishing reel repair rebuild tutorial Neptuna penn 349 cradle
Reel Repair by Alan Tani
October 16, 2017, 08:08:29 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Search Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: Neptuna penn 349 cradle  (Read 1298 times)
0 Members and 1 Guest are viewing this topic.
mikeysm
Member
*
Online Online

Posts: 438


« on: July 10, 2017, 10:12:20 AM »

Can someone tell me if the back end comes apart on the cradle rod seat.

Mike
Logged
Bill B (Tarfu)
Fish Nutritionist II
Sensei
Member
***
Online Online

Posts: 2304


Riverside, CA


« Reply #1 on: July 10, 2017, 12:49:53 PM »

Mike not sure which part you are referring to, but if it's the handle that is inserted into the cradle then it is more than likely epoxied in.  The one I worked on was a tight fit and held in place with a nail.  Pretty crude way of doing it.  When I rebuilt mine, I wound dacron line on the shaft and glued it in place.

I would try some boiling water and see if that loosens it.

Bill
Logged

It may not be very productive,
but it's sure going to be interesting!
54bullseye
Member
*
Online Online

Posts: 115


« Reply #2 on: July 10, 2017, 01:31:47 PM »

If your talking the wooden butt end I think boiling water might swell the wood and make it harder to get out. But a lot of Nep-Tuna butts were fiberglass with rubber grips so depends on material. Post a few pictures and maybe we can help.
John Taylor
Logged
Vintage Offshore Tackle
Photo Group
Member
**
Online Online

Posts: 731



« Reply #3 on: July 10, 2017, 02:17:01 PM »

Mike, most of them are glued but I have seen two that had threaded fittings so you could take the butt off but leave the reel rigged up on the rod, an early version of the Aftco Storabutt.
Logged
mikeysm
Member
*
Online Online

Posts: 438


« Reply #4 on: July 10, 2017, 06:16:07 PM »

Thanks for the information I wanted to work on the butt section. But the wood is in good shape. It also needs a new Ferell its a early style. I will machine a newer style that locks in place.

Mike


* 20170710_192144.jpg (260.46 KB, 1280x720 - viewed 22 times.)
« Last Edit: July 10, 2017, 06:26:13 PM by mikeysm » Logged
Bill B (Tarfu)
Fish Nutritionist II
Sensei
Member
***
Online Online

Posts: 2304


Riverside, CA


« Reply #5 on: July 10, 2017, 06:49:53 PM »

Mike I see yours got the Swiss Cheese treatment too....drilled for 349 and 49.....Your butt section is most likely glued in.....a careful application of a heat gun should melt the glue holding the butt in the cradle...CAREFUL is the key word here brother.....unless you do not mind sacrificing the finish on the butt as there does not appear to be any finish on the cradle it's self....Bill
« Last Edit: July 10, 2017, 06:51:00 PM by TARFU » Logged

It may not be very productive,
but it's sure going to be interesting!
mikeysm
Member
*
Online Online

Posts: 438


« Reply #6 on: July 10, 2017, 07:11:48 PM »

The holes I believe are factory drilled for either reel. I want to anodize the frame. I also may want to change the butt section. One screw broke off and needs to be drilled out. I have a 5-40 heli coil kit coming if necessary. Where do i find a blank that fits the ferell.

Mike


* 20170810_122528.jpg (387.23 KB, 1280x720 - viewed 17 times.)
« Last Edit: August 10, 2017, 03:44:27 PM by mikeysm » Logged
The Great Maudu
Member
*
Online Online

Posts: 364


I'd rather be hearing the clickers scream


« Reply #7 on: September 19, 2017, 09:01:09 PM »

Measure the ID of your ferrule. Check out suppliers sites that sell blanks. You will be able to find one that comes close. Use masking tape to get a snug fit, Epoxy the blank butt into the ferrule and you're good to go.
Logged
droppedit
Member
*
Online Online

Posts: 71



« Reply #8 on: September 20, 2017, 12:22:36 PM »

Most all the blank catalogs show the butt diameter. When gluing in the rod to the ferrule 2 things to think of. If it is a keyed ferrule make sure you spine the rod to the key. Also scuff up the inside of the ferrule and the same to the outside of the blank. This will allow the epoxy to bond better and have less risk of slipping under pressure. I've always used Rod Bond for this. As long as it is mixed right there shouldn't be any problems.


Dave
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Simple Audio Video Embedder
Valid XHTML 1.0! Valid CSS!
Page created in 0.123 seconds with 16 queries.