alan tani @ alantani.com fishing reel repair rebuild tutorial How do I remove this cog wheel--Abu 4600?
Reel Repair by Alan Tani
December 13, 2018, 05:33:19 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Search Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: How do I remove this cog wheel--Abu 4600?  (Read 822 times)
0 Members and 1 Guest are viewing this topic.
festus
Photo Group
Member
**
Offline Offline

Posts: 660



« on: November 12, 2017, 04:34:06 PM »

This cog wheel has no c-clip or screw holding it on, never seen one like it.  The schematic doesn't show a fastener, could it just snap off?


* 4600.JPG (43.41 KB, 412x355 - viewed 206 times.)

* 4600-1.jpg (627.86 KB, 1130x1051 - viewed 86 times.)

* 4600-2.jpg (1265.68 KB, 1365x1548 - viewed 87 times.)

* 4600-3.jpg (2654.27 KB, 2000x2470 - viewed 68 times.)
Logged
handi2
Sensei
Member
***
Online Online

Posts: 3260


OCD Reel Service and Repair


« Reply #1 on: November 12, 2017, 05:01:28 PM »

I use a heavy piece of monofilament line. It will pop right off. Try to get a line that will fit in between the plastic teeth of the gear.
Logged

OCD Reel Service & Repair
Gulf Breeze, FL
festus
Photo Group
Member
**
Offline Offline

Posts: 660



« Reply #2 on: November 12, 2017, 05:24:53 PM »

Thanks Handi, is it best to fit the mono between the teeth of the little top gear or the bigger bottom gear?
Logged
Rancanfish
Member
*
Offline Offline

Posts: 1727


« Reply #3 on: November 12, 2017, 07:29:14 PM »

I would think you would slide it under the large one and toward the center.
Logged

Can't sleep, clowns will eat me.
GulfOfBothnia
Member
*
Offline Offline

Posts: 135


« Reply #4 on: November 13, 2017, 01:12:31 PM »

There are small "ears" close to the shaft. Bend them outwards a little using a small flat screwdriver and simultaneously lift the cog wheel upwards. It should pop out. Just did it a few minutes ago.
Logged
festus
Photo Group
Member
**
Offline Offline

Posts: 660



« Reply #5 on: November 14, 2017, 05:10:54 PM »

There are small "ears" close to the shaft. Bend them outwards a little using a small flat screwdriver and simultaneously lift the cog wheel upwards. It should pop out. Just did it a few minutes ago.
Yup, I got it out following those instructions.  The last couple days I've serviced two more round Abus with the same setup, a 5500 HCL and a Royal Express I, along with the 4600. 


* abu hcl dsssmbld.jpg (1615.96 KB, 3474x2045 - viewed 81 times.)

* ryl xprss dsssmbld.jpg (1269.87 KB, 3344x1542 - viewed 72 times.)
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Simple Audio Video Embedder
Valid XHTML 1.0! Valid CSS!
Page created in 0.196 seconds with 18 queries.