Easy Fix for Power Drills & Drivers

Started by foakes, April 07, 2021, 10:12:35 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

foakes

Nearly 20 years ago, my wife got me a DeWalt 18V XRP, 3-speed 1/2" drill/driver, with torque settings.

It was not cheap at the time — around $250.

It has been used extensively for every type of job — from deck-building to remodeling to raising the camper jacks — in every type of weather from heavy snow to rain to 100 degree+ days.

Last Friday, I went to use it — and the motor started to smoke.  Even though this was a quality tool, it was 20 years old — so I figured it was toast.  However, being cheap, I decided to check symptoms online.  Went to a YouTube that showed very clearly my issue — the fix was new brushes.

Ordered them last Friday online from Tool-Center back in Tennessee.  Showed up today via UPS.  

$14.92 — delivered, including tax.

5 minute job — Yamaha grease on the gears while I had it apart.  Runs as good as new!

It took a T6 torx to remove the 4 screws at the back of the housing.  Couldn't be easier.

Best, Fred
The Official, Un-Authorized Service and Restoration Center for quality vintage spinning reels.

D-A-M Quick, Penn, Mitchell, and ABU/Zebco Cardinals

--------

The first rule of fishing is to fish where the fish are. The second rule of fishing is to never forget the first rule.

"Enjoy the little things in Life — For someday, you may look back — and realize that they were the big things"
                                                     Fred O.

Dominick

Nice work Fred.  Did you have to trim and cut the commutator?  I remember rebuilding car generators when I was a teen.  We would fine sandpaper the commutator and run a thin hacksaw blade in the groves.  I bet you already know this but if you can see sparks when the drill is running you may have to do so to keep the new brushes from wearing out.  Dominick
Leave the gun.  Take the cannolis.

There are two things I don't like about fishing.  Getting up early in the morning and boats.  The rest of it is fun.

foakes

Quote from: Dominick on April 07, 2021, 10:47:27 PM
Nice work Fred.  Did you have to trim and cut the commutator?  I remember rebuilding car generators when I was a teen.  We would fine sandpaper the commutator and run a thin hacksaw blade in the groves.  I bet you already know this but if you can see sparks when the drill is running you may have to do so to keep the new brushes from wearing out.  Dominick

No, I did not know that, Dominick — Thanks, I'll check for sparks — makes sense!

Best, Fred
The Official, Un-Authorized Service and Restoration Center for quality vintage spinning reels.

D-A-M Quick, Penn, Mitchell, and ABU/Zebco Cardinals

--------

The first rule of fishing is to fish where the fish are. The second rule of fishing is to never forget the first rule.

"Enjoy the little things in Life — For someday, you may look back — and realize that they were the big things"
                                                     Fred O.

Wompus Cat

Quote from: Dominick on April 07, 2021, 10:47:27 PM
Nice work Fred.  Did you have to trim and cut the commutator?  I remember rebuilding car generators when I was a teen.  We would fine sandpaper the commutator and run a thin hacksaw blade in the groves.  I bet you already know this but if you can see sparks when the drill is running you may have to do so to keep the new brushes from wearing out.  Dominick

You are going back a few years here . We use to chuck the Armatures in a lathe and machine down the Commutator, Put the thing on a Growler to test continuity ,replace bearings,fields,bushings,Brushes. We rebuilt water pumps,starters,brake master cylinders ,Starters,Carburetors, Cylinder Heads,Re- line the Brake Shoes,,,,just about everything on the car .
Now days the Technicians got to the parts dept with a cart and chuck whatever is available in it and stick it on the car and sometimes it will fix it .
No More Mechanics on the Planet besides the ones here ...lol
If a Grass Hopper Carried a Shotgun then the Birds wouldn't MESS with Him

foakes

Quote from: Dominick on April 07, 2021, 10:47:27 PM
if you can see sparks when the drill is running you may have to do so to keep the new brushes from wearing out.  Dominick

Took it in the closet, and peered in — no sparks!  Good for another 20 years...

Thanks,

Fred
The Official, Un-Authorized Service and Restoration Center for quality vintage spinning reels.

D-A-M Quick, Penn, Mitchell, and ABU/Zebco Cardinals

--------

The first rule of fishing is to fish where the fish are. The second rule of fishing is to never forget the first rule.

"Enjoy the little things in Life — For someday, you may look back — and realize that they were the big things"
                                                     Fred O.

Midway Tommy

Had a similar issue with a nice little handy metal Craftsman 3 X 21 belt sander I bought new in '73 a couple of years ago. It sparked & chattered a couple of times so I figured it had seen it's better days. Went to use it one day & it wouldn't even start so I took the bushes out & flipped them around (kept them on the same sides) & voila, it was working again. New brushes were only a couple of bucks & it now runs almost like new.
Love those open face spinning reels! (Especially ABU & ABU/Zebco Cardinals)

Tommy D (ORCA), NE



Favorite Activity? ............... In our boat fishing
RELAXING w/ MY BEST FRIEND (My wife Bonnie)

alantani

#6
this is so weird.  my 3/8ths inch corded dewalt just decided to take a dump on me tonight.  i started looking around and figured i'd just order another and tossed the old on in the trash.  so before going on line, i check here.  i just ordered a set of brushes for $5.  
send me an email at alantani@yahoo.com for questions!

thorhammer

Cal's in the chuck clutches, don't forget!!!

I've got a favorite Milwaukee from about 2000 that has bit the dust....I've kept hoping a motor would turn up; I "overused" it on a particularly tough job that kilt it. That's "killed" if you aren't Greg or from the South :)

I'll give brushes a shot.