alan tani @ alantani.com fishing reel repair rebuild tutorial Penn 200 Clicker Replacement
Reel Repair by Alan Tani
October 21, 2018, 05:16:28 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Search Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: Penn 200 Clicker Replacement  (Read 1595 times)
0 Members and 1 Guest are viewing this topic.
RJELECTRIC
Member
*
Offline Offline

Posts: 4


« on: November 02, 2012, 03:53:28 PM »

 I have to replace the clicker tongue in my 200 surfmaster. I drilled out the existing button and tongue and ordered new ones from mysticparts.com. The website says to "peen" the new one into place. I'm not quite sure what that means. Is there a procedure for this? I can't seem to find much info on this topic. I'd be greatful for any advice. Thanks Ron


"Edited as per Moderators to correct Scott's Bait & Tackle over to their new store name Mystic Reel Parts / www.mysticparts.com"
« Last Edit: August 09, 2018, 09:54:39 AM by mizmo67 » Logged
Cone
Firearms Group
Member
**
Offline Offline

Posts: 1226



« Reply #1 on: November 02, 2012, 04:13:43 PM »

Peening is displacing metal. You will have to assemble it together and tap it to spread the metal so it wont come apart. Poor description but I'm sure with the parts in your hand you'll figure it out. Bob
Logged

"Quemadmoeum gladuis neminem occidit, occidentis telum est." (A sword is never a killer, it is a tool in the killer's hands.)
   -    Lucius Annaeus Seneca, circa 4 BC – 65 AD
Irish Jigger
Member
*
Offline Offline

Posts: 1346

Northern Ireland.


« Reply #2 on: November 02, 2012, 04:15:12 PM »

Before you "peen" ie rivet the Click Button /Click Tongue together I would  check if a three part replacement assembly comprising,Click Tongue,Click Button and Retaining Ring is available for this reel. No "peening" required.
Logged
mizmo67
MysticParts.com Sales/Tech
Moderator
Member
****
Offline Offline

Posts: 1118


Mystic Island, NJ


WWW
« Reply #3 on: August 09, 2018, 09:55:44 AM »

I've added a better description of the process to the parts in our online store that need peening done, so hope that helps folks in the future.
Logged

~Mo

Maureen Albertson Smiley
Scott's Bait & Tackle / Mystic Reel Parts (Formerly PennParts.com)
Contact Me Via Store Website Please!
Orders/Support# +1 (609) 488-4637 (parts ordering or troubleshooting)
Skype: mysticreelparts
scrinch
Member
*
Online Online

Posts: 127



« Reply #4 on: August 09, 2018, 10:10:33 PM »

Just a warning....this isn't something that's usually done indoors. You don't want visitors to see you peen in your shop, so you should take the tools and do it out by the back fence!   Wink
Logged
oc1
Sensei
Member
***
Online Online

Posts: 1821



« Reply #5 on: August 10, 2018, 12:30:13 AM »

The important thing is to make sure the click button on the outside is supported on something solid and the bakelite is not touching anything solid.  When you whack the end of the shaft on the inside, you want all the force to go into the button shaft and then the anvil or other hard surface.  Otherwise, you will blow out the plastic side plate.  You will also need a punch about the diameter of the button shaft or a little smaller.  Trying to hit it directly with a hammer is courting disaster.  I'm one out of two and will get the 'C' clip thing next time.
-steve
« Last Edit: August 10, 2018, 12:37:22 AM by oc1 » Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Simple Audio Video Embedder
Valid XHTML 1.0! Valid CSS!
Page created in 0.216 seconds with 16 queries.