alan tani @ alantani.com fishing reel repair rebuild tutorial electramate 6/0 gear sleeve
Reel Repair by Alan Tani
April 20, 2018, 12:23:22 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Search Login Register  
Pages: 1 [2]   Go Down
  Print  
Author Topic: electramate 6/0 gear sleeve  (Read 10898 times)
0 Members and 1 Guest are viewing this topic.
Alto Mare
Moderator
Member
****
Online Online

Posts: 11043


Southeastern Pennsylvania


« Reply #15 on: June 09, 2012, 06:35:07 PM »

Dan, I'm glad that you posted that picture. The plate that you're showing was discontinued by Penn but I don't recall the reason, you have an injection molded plate. Do you mind showing us one shot of the plate without the dogs? It appears that you didn't have to do much shaving, nice job by the way. You could make those dogs engage at the same time, from the 15-114H to the 15-116, the dogs  lenght goes up by appr. 1/8". I'm sure if you install one 15-114H and one 15-115, the dogs would engage at the same time. Lee might have some ready for us. Thanks again for showing. Sal
Logged

Forget about all the reasons why something may not work. You only need to find one good reason why it will.
Bryan Young
Ultimate Upgrades Drags
Administrator
Member
*****
Offline Offline

Posts: 9656


The Reel Whisperer


« Reply #16 on: June 09, 2012, 07:49:05 PM »

I was about to grind mine down so that they would mate up or completely alternate halfway inbetween.  Hmm, decisions...
Logged

Cheesy I talk with every part I send out and each reel I repair so that they perform at the top of their game. Cheesy
Alto Mare
Moderator
Member
****
Online Online

Posts: 11043


Southeastern Pennsylvania


« Reply #17 on: June 09, 2012, 07:57:19 PM »

Six in one hand and a half dozen on the other Bryan, I would wait for the 15-115. You might still have to do a little filing, but I'm sure  it won't be much.
Logged

Forget about all the reasons why something may not work. You only need to find one good reason why it will.
Alto Mare
Moderator
Member
****
Online Online

Posts: 11043


Southeastern Pennsylvania


« Reply #18 on: June 09, 2012, 08:11:15 PM »

Ok Dan, I just remembered about those plates:
http://www.google.com/url?sa=t&rct=j&q=penn%20injection%20plates%20bulletin&source=web&cd=1&sqi=2&ved=0CGMQFjAA&url=http%3A%2F%2Fpennreels.com%2Fsites%2Fall%2Fthemes%2Fpenn%2Fimages%2Frepairbulletin1.pdf&ei=Vx3UT8GKLabH0AG5o5H7Ag&usg=AFQjCNFCgrgC89sPMvm3g4Qt91AKwVamjQ.
But don't worry, the ones that I know about never had a problem.
Logged

Forget about all the reasons why something may not work. You only need to find one good reason why it will.
Bryan Young
Ultimate Upgrades Drags
Administrator
Member
*****
Offline Offline

Posts: 9656


The Reel Whisperer


« Reply #19 on: June 09, 2012, 09:08:19 PM »

Thats good that that plate didn't have a problem because that is what my plate looks like.  Funny, mine works out with ratcheting every other, almost the middle of each Rachel, which is what I wanted, but not the same as Dan's.
Logged

Cheesy I talk with every part I send out and each reel I repair so that they perform at the top of their game. Cheesy
suitekids
Member
*
Online Online

Posts: 157


« Reply #20 on: June 09, 2012, 11:28:11 PM »

Hi again guys, here is a pic without the dogs installed and alongside the replacement sideplate on the left (compression molded) for comparison, Sal, this is the pic you wanted right?

Logged
Alto Mare
Moderator
Member
****
Online Online

Posts: 11043


Southeastern Pennsylvania


« Reply #21 on: June 10, 2012, 02:33:57 AM »

Thanks Dan, I appreciate the shot. What you have there are plates that are made to swing left to right. You only needed to shave a little by the new dog area.... just as I suspected. For those of you that have the 1-114H that is molded to swing left to right, go for it, it's fairly easy. On the 113H, it's not worth the effort.
Logged

Forget about all the reasons why something may not work. You only need to find one good reason why it will.
suitekids
Member
*
Online Online

Posts: 157


« Reply #22 on: June 10, 2012, 04:44:44 AM »

There is another small thing to consider, the little section you shave out to fit the second dog is also acting as a tab to support the bridge before it freespans to the sleeve just after the screw. I don't know how much deflection of the bridge plate occurs under load across that open span, but I suspect that more support would be better. I also think the 6/0 bridge is very stout and I'm being over cautious, just my structural construction background...  Undecided Undecided
Logged
Alto Mare
Moderator
Member
****
Online Online

Posts: 11043


Southeastern Pennsylvania


« Reply #23 on: June 10, 2012, 04:58:53 AM »

I also have a little structural construction background and have corrected architects a few times in the past Grin. I do not believe that shaving the area as I did on my Reel/Tank would cause any problems, there is enough material left to support the bridge plate. As everything else, the proof is in the pudding! As of now, I do not have any issues with mine.
I also want to add that most of the stress is absorbed by the frame itself, there isn't much sideway pressure on a reel under load. When a reel twists under load, as they do with graphite frames, that's when you'll have frames and gears problems. Tiburon has it right with their new frames, eliminating the inner rings creates one unit with the frame and plates. A reel that doesn't twist under load is a happy reel.
This is only my opinion.
Take care. Sal
« Last Edit: June 11, 2012, 01:40:45 AM by Alto Mare » Logged

Forget about all the reasons why something may not work. You only need to find one good reason why it will.
shadfun
Member
*
Offline Offline

Posts: 2


« Reply #24 on: January 09, 2018, 08:16:28 PM »

i have not done the final QA check on them.  i am charging $28 for now, but that will go up as soon as pennparts.com get's they shipment.  these suckers are HUGE! Grin
Hi can I have couple of this parts for my Penn 6/0 and 9/0. thanks
Logged
Shark Hunter
Moderator
Member
****
Online Online

Posts: 9993


The Rogue of the Seven Seas!


« Reply #25 on: January 09, 2018, 08:39:39 PM »

Being this post is 6 years old. I'm not sure if alan still has them in stock.
Cortez Conversions has them in a ten tooth version.
https://www.cortezconversions.com/ss-gear-sleeves
Penn parts also has these if alan can't help.
https://store.scottsbt.com/98-114AT-Sleeve-Gear-Sleeve-comes-with-pin-Stainless-Optional-P27673.aspx
Logged

Life is Good!
twotone
Sensei
Member
***
Offline Offline

Posts: 278



« Reply #26 on: January 10, 2018, 03:07:42 PM »

This post reminded me to ask this?  Is this 6/0 sleeve on the left an ElectraMate sleeve?
I ran across this 114h sleeve in a easy access drag plate.


* 20180109_172051.jpg (3244.99 KB, 5312x2988 - viewed 135 times.)
Logged
Shark Hunter
Moderator
Member
****
Online Online

Posts: 9993


The Rogue of the Seven Seas!


« Reply #27 on: January 10, 2018, 10:18:06 PM »

Its hard telling Anthony.
I'd say with that straight shaft. Probably not.
It was probably made by someone here.
Logged

Life is Good!
alantani
admin
Administrator
Member
*****
Online Online

Posts: 15429



« Reply #28 on: January 11, 2018, 12:45:35 PM »

that's one of mine!
Logged

send me an email at alantani@yahoo.com for questions!
twotone
Sensei
Member
***
Offline Offline

Posts: 278



« Reply #29 on: January 11, 2018, 01:25:12 PM »

Didn't remember seeing any center hole at the bottom of any other stainless sleeve. I do see them on brass ones.


Thx 
Logged
Pages: 1 [2]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Simple Audio Video Embedder
Valid XHTML 1.0! Valid CSS!
Page created in 0.449 seconds with 16 queries.