Quote from: kamuwela on March 12, 2010, 04:30:24 AM
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A001.jpg?t=1268361931)
We have a brand new Shimano 130A, grab a schematic & follow along.
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A002.jpg)
Remove push button shield #91 & two screws #92
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A003.jpg)
Remove slide plate #94 & handle bolt plate #2A
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A004.jpg)
Remove push low button shaft #740 & handle assembly #741
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A005.jpg)
Remove drive shaft shield
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A006.jpg)
Remove lever hub cover #414 & lever quadrant #743
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A009.jpg)
Remove right side plate B #746
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A011.jpg)
Right side plate B & drive gear assembly
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A012.jpg)
Pinion gear & alert ratchet #750
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A013.jpg)
Main gear assmebly with inner & outter bearings #578 looks dry for my liking but it was lubricated
with a liquid lube
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A014.jpg)
Remove spool #751
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A017.jpg)
Left side plate #758
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A018.jpg)
Remove harness lug #756
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A020.jpg)
Remove stand #459
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A021.jpg)
Remove stand shield #458
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A022.jpg)
Okay, here we go. This is my theory of corrosion protection. These reels arent cheap i
guess im just picky. It should last a life time.
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A024.jpg)
Grease all screw holes to prevent salt intrusion
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A025.jpg)
I like to also to brush screws with grease
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A026.jpg)
Torque them down & wipe away excess grease
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A027.jpg)
Lightly grease all screw holes, one piece #757. Dont use too much grease, prevent frame
cracking tighten screws slowly & torque tight
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A028.jpg)
Grease frame & install harness lug
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A033.jpg)
Repack all bearings
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A034.jpg)
Lightly coat left side plate just more salt protection
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A036.jpg)
A light coat of grease & a bead for a seal along the outter edge
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A037.jpg)
Grease screw holes for more protection
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A039.jpg)
Install left side plate cover & wipe off excess grease
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A041.jpg)
Remove cross pin #441 & preload springs #444
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A042.jpg)
Remove anti-reverse ratchet #461
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A043.jpg)
Remove cooling shield #754
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A046.jpg)
Remove outter drag washer & drag plate #752
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A047.jpg)
Two shims & liquid lubed bearings. dont think i'll be casting this real so i'll just repack bearings
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A049.jpg)
Note: four pressure release springs #448
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A052.jpg)
Repacked spool bearing #577
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A053.jpg)
Greased drag washers inner & outter #454 & #449
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A054.jpg)
Wipe off excess grease
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A055.jpg)
Insert pressure plate A #449 & grease pressure release spring #448
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A056.jpg)
Lightly grease O ring & cooling shield #754
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A057.jpg)
Install pressure plate B #454
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A058.jpg)
Install anti-reverse ratchet #461 & shim
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A059.jpg)
Reinstall right side pinion assembly. note: this reel 2 shims then spring washers.
washers were reinstalled using stock configuration ((((|
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A060.jpg)
Install completed spool
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A061.jpg)
Going to lightly grease main gear assmebly & repack bearings
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A062.jpg)
One drop of corrosion X on alert plunger #749
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A063.jpg)
Lightly grease shaft, install shim on drive gear B #438 drive gear A #437
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A064.jpg)
Salt protection complete
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A065.jpg)
Installl lever quadrant #743,drag control lever #745 & lever hub cover #416
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A066.jpg)
Grease drive shaft shield #409 & install with drive shaft thrust washer #410 & #411
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A067.jpg)
Reinstall handle
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A068.jpg)
Note: little spring, dont lose it. Install handle bolt plate 2A, slide plate #94, slide plate
spring #93, & push button shield #91
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A069.jpg)
(http://i771.photobucket.com/albums/xx358/r_willis62/shimanoT130A001.jpg)
Now that wasnt so hard was it? There were a few little springs here & there that could
be lost easily. These are great reel in my opinion, could use more lubrication from the
factory. I mean i dont think too many guys will use these reels for casting. If you look
at a previous tutorial i did, you can see the beating these reels take here in Hawaii. For
me, its all aout protecting the investment.
Aloha, Kamu
Honolulu