I came across another one of these 8000 series reels in less than stellar condition, but it appeared to be complete. The seller wanted $20 but had "make an offer" in the listing, so I offered 10 bucks. Lo and behold...the next morning I had a notification to pay up! This ad from the period describes the features of the reel, and it certainly does sound like a fine reel.
(https://flic.kr/p/2i8XsQ9)
Since once again my reel had no badge, I wasn't sure whether I had the 8600 or 8700, so I used this ad to check the weight. My reel weighed 18.75 oz., so it looks like I have the 8700.
(https://flic.kr/p/2i926z4)
Well...here she is...so ugly she'd have to sneak up on water just to get a drink. :D Not much sense in working on appearance, I'll just make this one fully functional and fish it.
(https://flic.kr/p/2i926yx)
The first look inside found things uglier than the outside. We'll need to scrape away some crud just to see what we even have here.
(https://flic.kr/p/2i911mu)
Now that I can actually see parts...I notice the gearing is different than the little 8100 I posted a few weeks ago. The 8100 had brass drive and pinion gears, while this 8700 has a machined alloy drive and a chromed steel pinion.(the red arrow points to a magnet on the pinion) The green arrows indicate the drive shaft bearings, which were both stuck fast to their mountings. I'll have to assume the indifferent metals are the source of the trouble here. Past experience with these lighter build ball bearings tells me I have no need to stress them by twisting and pulling. These type bearings can be ripped apart if you aren't careful. I have a much easier way to clean these without disturbing them.
(https://flic.kr/p/2i9267L)
Hold the parts over the sink and squirt the Paslode into the bearing from below it. This will force out the old lube and all the crud, and drip right off the bearing. Spin the bearing a few times and give it another blast. It is now clean and dry.
(https://flic.kr/p/2i8XsGt)
Inside the rotor gives a pretty good indication this reel was fished in the surf. The bail was bogged down with beach as well, and had to be completely torn down and bathed.
(https://flic.kr/p/2i8XsEQ)
The handle...sheesh...what a wreck. Evidently at some time a truck had ran over the handle. Then a previous owner used channel locks and vice grips to "straighten" it. The knob shaft was trashed...all loose and busted up...so I put an aftermarket piece on. I polished the handle blade the best I could, but it wears the scars of idiocy. Patina from years of normal use is lovely, but vice grip damage sucks. :-\
(https://flic.kr/p/2i8XsCR)
All the literature I've seen on these 8000s indicates they used teflon drags, yet this one had leather. The only teflon was the underspool washer. I cleaned up the drags and tested them...and could only get 3.5-4lbs. fully cranked down. Maybe it was the leathers, as they were thin and well burned. Also teflon is not the best choice in a large reel like this, as it tends to squish out at higher settings. I subbed in some hard fiber washers which easily hit 8 pounds of smooth pull, so I called it good, as that is about the range I'd want for this reel.
(https://flic.kr/p/2i926nF)
Here are all the cleaned parts, the new handle knob, and the new drags. If you zoom on the photo you can see where a bit of the chrome has chipped off the pinion.
(https://flic.kr/p/2i93tLh)
I buffed the raised letters and ring surrounding the missing badge. Call it lipstick on a pig...HA! ;D
(https://flic.kr/p/2i926hL)
Kevin mentioned this bail ramp and trip worked very well on these 8000s, and I agree. This is how a bail should trip. I
despise when the bail trip just about yanks the reel from your hands.
(https://flic.kr/p/2i926dY)
After reassembling the reel I was very pleased with the feel...can't wait to get it wet! 8)
(https://flic.kr/p/2i926by)
(https://flic.kr/p/2i8XsmD)
(https://flic.kr/p/2i8XsiN)
Thanks Mo, that's a solid reel! Definitely not a shelf queen but will do the job haulin' cats for you!
Cheers,
Andrew
Nice job Mo!
That's definitely diamond in the rough and a great workhorse!
That's undoubtedly a strong reel and would be perfect for bank fishing for big catfish. Perfect for rocky shoreline where you don't want to take your looker reels. Even bigger than my 8600 which would probably take on anything here in Tennessee.
Rotor and spool larger on 8700 than the 8600. I picked up a beater a few years ago. Fortunately the gearbox was packed with grease so the internals were in excellent shape. Serves as one of my wife's catfishing reels. One drawback to these reels is that the bail doesn't flip back far enough to clear the line when casting. Not an issue for what I am using it for. Still considering modifying the bail to lock back a bit.
That turned out nice considering how it arrived! That bail trip is really smooth. So is the 8100 which has no ramp but the larger ones are really easy to trip.
Thanks fellas. I put 50lb. braid with a 30lb. 20ft. mono leader on the reel today. I clamped it on a 9 ft. rod and it chucked a 4oz. bank sinker great...60-70yds. just tossing it. 8)
Quote from: Chuck750ss on January 03, 2020, 01:41:40 AM
One drawback to these reels is that the bail doesn't flip back far enough to clear the line when casting. Not an issue for what I am using it for. Still considering modifying the bail to lock back a bit.
I'm wondering if maybe your bail was tweaked at some point. I checked mine and it clears the line. The braid I used doesn't stack onto the spool perfectly...it tends to build up in the middle. This would be a disaster for distance casting, but no farther than I chuck a bait, it will work just fine. I corrected the line lay by hand while spooling up, so below my casting distance the line is level. I'm not removing enough line on a cast to make the center heavy line lay a problem.
My bail doesn't interfere with the line while casting either. Mine also doesn't stack line higher in the middle of the spool. That is an unusual problem to have. I've seen different reels stack high or low on a spool which is usually pretty easy to fix...not sure what you could do with heavy center line lay.
Quote from: The Fishing Hobby on January 10, 2020, 12:08:34 PM
My bail doesn't interfere with the line while casting either. Mine also doesn't stack line higher in the middle of the spool. That is an unusual problem to have.
It only stacks high in the center with braid Kevin...it spreads out normal with mono. I've actually had this problem with other classic reels designed for mono. As you can see from the last photo I posted, the line lay looks pretty good when you keep it corrected below the "casting length". That pic shows the line rewound after a cast...almost a straight line lay. I probably made the problem sound worse than it really is. 8)
Great ingenuity in that repair Mo! Love it!
These are really cool reels!
Sometimes "a guy's just gotta do what a guy's gotta do".
Innovative and well done, Mike!
Nice work bringing those reels back to life!
Simple fix for a part it might take years to find a replacement. Good job, Michael.
That 8700 must be a hoss. Biggest I have is the 8600 and it's difficult to imagine an even bigger one.
You're a clever guy Mo.
-steve
Quote from: The Fishing Hobby on January 10, 2020, 12:08:34 PM
My bail doesn't interfere with the line while casting either. Mine also doesn't stack line higher in the middle of the spool. That is an unusual problem to have. I've seen different reels stack high or low on a spool which is usually pretty easy to fix...not sure what you could do with heavy center line lay.
Kevin, 2 8700's, Penn 704 in middle for comparison. Notice that the 704 bail flips back further, completely clearing any line coming off the reel.
Quote from: festus on March 18, 2020, 10:24:21 PM
Simple fix for a part it might take years to find a replacement. Good job, Michael.
That 8700 must be a hoss. Biggest I have is the 8600 and it's difficult to imagine an even bigger one.
Same reel except 8700 has bigger rotor and spool. 8600 spool will work on 8700.
Quote from: Chuck750ss on March 31, 2020, 02:14:51 AM
[ Notice that the 704 bail flips back further, completely clearing any line coming off the reel.
Thanks for posting that pic Chuck. I think it may have helped me crack this case. I looked at my reel and tried to imagine what would cause the bail to only open half way. Then I remembered that bottom bail arm will spin on the bail. I zoomed on your pic and there it was...they are on upside down! I turned mine over just to confirm, and sure as a day is long, the bail only opened half way. I took a pic of the correct side up and below it is the wrong side up. Note the bail position in the pics. 8)
Yep! Post a problem and one of our reel geniuses will figure it out. Nice work Mo. Dominick
Thanks. I own 2 8700's and a 8600. All are like that. BTW, all 3 were purchased like that. Should have had my thinking cap on. And I did not! Not a first for me though.
Quote from: Chuck750ss on March 31, 2020, 07:10:51 PM
Thanks.
You are welcome. You mentioned earlier your wife used these reels...I bet she'll cast 'em like a bullet now! Glad I could help. 8)
Mo, these are excellent catfishing reels. Along with Shakespeare 2090/91.
Quote from: mo65 on January 02, 2020, 10:04:34 PM
(https://flic.kr/p/2i8XsiN)
I just received my 8700 in the mail. I have not had a chance to do anything but it spins freely and smoothly so that is good. May I ask where did you get the round knob for the handle?
Also, I just realize that the screw that attached the bail to the rotor, not sure what it is called, it is bent :( I appreciate if anyone has advice where to look for a replacement screw.
I just had someone asking me on my video about the 8700 and if there were any actually sold in the USA. I'll send him here to check yours out, thanks for the post MO!!!