reposted with permission. derrick, thank you very much! alan
http://www.fishingkaki.com/forum/viewtopic.php?t=126662
Quote from: Derrick Limhi all surf kakis,
by chance,i found that the sealine x shv/sha can be upgraded like a grandwave z,5 ball bearings and infinite anti reverse compare to 3 ball bearings and no infinite....and 2 different size ball bearing
1st of all,you need to order the following 4 parts from DAIWA and they are
1)6F827801(handle metal plate)
2)6E248101(handle metal plate screw)
3)6F827101(collar D)
4)6F827601(handle metal)
2nd,get 2 ball bearings of different locally and you are ready to transform your SHV/SHA into a GRANDWAVE Z!!!!
just following the steps and you should be able to modify your own reel.....
THESE ARE THE TOOLS YOU NEED AND PARTS FROM DAIWA
(http://www.fishingkaki.com/forum/files/img_1607_165.jpg)
A CLOSED UP LOOK ON THE PARTS FROM DAIWA
(http://www.fishingkaki.com/forum/files/img_1608_174.jpg)
UNSCREW THE HANDLE NUT SCREW
(http://www.fishingkaki.com/forum/files/img_1609_121.jpg)
REMOVE THE HANDLE NUT WITH THE SPECIAL TOOL FROM DAIWA
(http://www.fishingkaki.com/forum/files/img_1610_139.jpg)
TURN OUT THE STAR DRAG(ANTI CLOCKWISE)
(http://www.fishingkaki.com/forum/files/img_1611_113.jpg)
TAKE OUT THE DRAG CLICKER,DRAG SPRING WASHERS,BEARING WASHER AND BEARING IN ORDER
(http://www.fishingkaki.com/forum/files/img_1614_183.jpg)
REMOVE ALL 6 SCREWS FROM THE END PLATE
(http://www.fishingkaki.com/forum/files/img_1615_100.jpg)
THIS IS HOW THE INTERNAL SHOULD LOOK AFTER YOUHAVE OPEN IT
(http://www.fishingkaki.com/forum/files/img_1616_265.jpg)
WE ARE GOING TO REPLACE THE BUSHING WITH A BEARING
(http://www.fishingkaki.com/forum/files/img_1617_211.jpg)
BEARING VS BUSHING
(http://www.fishingkaki.com/forum/files/img_1620_213.jpg)
USE A SMALL SCREWDRIVER TO REMOVE THE RETAINER,BECAREFUL AS THE RETAINER CAN REALLY FLY!!
(http://www.fishingkaki.com/forum/files/img_1621_182.jpg)
AFTER THE RETAINER HAD BEEN REMOVE,TURN OVER,REMOVE THE CASTING CAP,TAKE OUT THE PINION SHAFT AND PUSH OUT THE BUSHING USING A SCREWDRIVER
(http://www.fishingkaki.com/forum/files/img_1622_238.jpg)
(http://www.fishingkaki.com/forum/files/img_1624_166.jpg)
SLOT IN THE BEARING AND PUT BACK THE RETAINER,MAKE SURE ALL 4 CORNERS ARE SITTED IN THE SLOT
(http://www.fishingkaki.com/forum/files/img_1625_101.jpg)
(http://www.fishingkaki.com/forum/files/img_1626_746.jpg)
(http://www.fishingkaki.com/forum/files/img_1627_126.jpg)
PUT BACK THE PINION SHAFT AND CLOSE BACK THE CASTING CAP
(http://www.fishingkaki.com/forum/files/img_1628_918.jpg)
NEXT IS THE INFINITE ANTI REVERSE,SLOT IN THE HANDLE METAL AND TURN SLIGHTLY,IT WILL SIT NICELY INTO THE GAP
(http://www.fishingkaki.com/forum/files/img_1629_128.jpg)
(http://www.fishingkaki.com/forum/files/img_1630_130.jpg)
PLACE THE HANDLE METAL PLATE OVER THE HANDLE METAL AND TIGHTEN WITH THE SMALL SCREW
(http://www.fishingkaki.com/forum/files/img_1633_545.jpg)
(http://www.fishingkaki.com/forum/files/img_1635_292.jpg)
NEXT,REPLACE THE ORGINAL COLLAR D WITH THE ONE FROM GRANDWAVE Z AND IT SHOULD SLOT INTO THE DRIVESHAFT WITH THE GAP FACING THE FRAME AND THERE SHOULD BE NO GAP IN BETWEEN
(http://www.fishingkaki.com/forum/files/img_1636_198.jpg)
(http://www.fishingkaki.com/forum/files/img_1637_141.jpg)
TIME TO CLOSE IT,MAKE SURE THAT THE PINION SHAFT SLOT INTO THE PINION GEAR AND THE CLUTCH CAM CATCHES THE YOKE PLATE,AFTER THAT GIVE THE CLUTCH LEVER A FEW PUSH JUST TO CONFIRM THAT THE ARM SIT IN THE YOKE PLATE
(http://www.fishingkaki.com/forum/files/img_1639_157.jpg)
(http://www.fishingkaki.com/forum/files/img_1643_106.jpg)
PUT EVERYTHING BACK IN ORDER
(http://www.fishingkaki.com/forum/files/img_1644_181.jpg)
(http://www.fishingkaki.com/forum/files/img_1645_143.jpg)
LOCK BACK THE 6 SCREWS AND THE 2 LONG ONE SHOULD BE AT THE BOTTOM
(http://www.fishingkaki.com/forum/files/img_1615_100.jpg)
PUT THE HANDLE BACK AND TIGHTEN THE HANDLE NUT AND STOP WHEN THE GROOVE OF THE NUT IS IN LINE WITH THE HOLE,FINALLY TIGHTEN THE HANDLE NUT SCREW
(http://www.fishingkaki.com/forum/files/img_1646_116.jpg)
(http://www.fishingkaki.com/forum/files/img_1647_181.jpg)
A UPGRADED SHA
(http://www.fishingkaki.com/forum/files/img_1648_536.jpg)
THE 3 MUSKETEERS OF DAIWA
DAIWA GRANDWAVE Z 30 SHW
DAIWA SEALINE X 30 SHA
DAIWA SEALINE X 30 SHV
(http://www.fishingkaki.com/forum/files/img_1649_205.jpg)
And can the SL20/30 SH series be upgraded the same way or no ?????
Hello all from Downunder,
Owning a string of SL20SH and SL50SH I am really interested in this post. I assume there are photos with this post but I can't view them. Is any one else having problems or just me.
Also seems the link is closed too.
Many thanks for great forum.
they are hosted on fishingkaki.com and i think their server is very slow. i might have to download the photos here and re-do the post. the upgrades look interesting, but the stock reels are reliable enough that the upgrades might not add that much. alan
I can't see any pictures either ???
Gotcha on the pictures.
Thanks Alan
Would the part numbers be different for a Sealine X 40SHA? I'm guessing they would.
Quote from: alantani on November 12, 2010, 07:47:59 AM
they are hosted on fishingkaki.com and i think their server is very slow. i might have to download the photos here and re-do the post. the upgrades look interesting, but the stock reels are reliable enough that the upgrades might not add that much. alan
Alan,
I know this is from 6 years ago . . . Any chance on being able to see those pics ?
Tight Lines !
Dave
Well, it's now 2021 and the pics are no where to be found.
However, for what little extra info it might provide, the Wayback Machine has the other forum thread archived.
https://web.archive.org/web/20120520055825/www.fishingkaki.com/forum/viewtopic.php?t=126662 (https://web.archive.org/web/20120520055825/www.fishingkaki.com/forum/viewtopic.php?t=126662)
Tight Lines !
Dave F.