Hot off the electronic presses.
New Carbontex Drag sizing chart.
Washer Number OD X ID X Thickness, mm(In.)
1 16 (0.613) X 8.25 (0.325) X 0.5 / 0.76 / 1 (0.02 / 0.03 / 0.04)
2 16.8 (0.66) X 4.3 (0.169) X 1 (0.04)
3 16.95 (0.666) X 5.95 (0.235) X 1 (0.04)
4 17.15 (0.675) X 9.35 (0.368) X 0.5 (0.025)
5 17.8 (0.7) X 10.35 (0.407) X 0.76 (0.03)
6 18.25 (0.72) X 8.35 (0.33) X 1 (0.04)
7 18.75 (0.735) X 10.9 (0.43) X 1 (0.04)
8 19.5 (0.765) X 4.2 (0.165) X 1 (0.04)
9 20.5 (0.805) X 10.85 (0.43) X 0.76 (0.03)
10 20.5 (0.81) X 8.1 (0.32) X 0.5 (0.02)
11 20.65 (0.81) X 8.9 (0.35) X 1 (0.04)
12 20.7 (0.815) X 13.15 (0.518) X 0.76 (0.03)
13 21.28 (0.84) X 5.18 (0.205) X 1 (0.04)
14 21.5 (0.85) X 8.1 (0.32) X 0.76 / 1 (0.03 / 0.04)
15 21.6 (0.85) X 10.6 (0.415) X 0.76 (0.03)
16 22.6 (0.89) X 12.7 (0.5) X 1 (0.04)
17 22.95 (0.905) X 8.3 (0.325) X 1 (0.04)
18 22.98 (0.095) X 8.15 (0.32) X 0.5 / 0.76 (0.020 / 0.03)
19 23.9 (0.94) X 11.3 (0.445) X 1 (0.04)
20 24.15 (0.95) X 14.5 (0.572) X 1 (0.04)
21 24.55 (0.965) X 10.6 (0.415) X 0.5 / 0.76 (0.020 / 0.03)
22 24.6 (0.97) X 14.5 (0.57) X 0.76 (0.03)
23 24.63 (0.969) X 5 (0.198) X 1 (0.04)
24 24.65 (0.97) X 19.3 (0.76) X 0.76 (0.03)
25 25.3 (0.995) X 17.05 (0.675) X 1 (0.04)
26 25.4 (1) X 8.4 (0.33) X 0.76 / 1 (0.03 / 0.04)
27 25.5 (1) X 8.65 (0.34) X 0.5 (0.02)
28 25.8 (1.015) X 18.7 (0.735) X 1 (0.04)
29 25.8 (1.015) X 10.75 (0.425) X 2 (0.08)
30 25.95 (1.02) X 19.25 (0.76) X 1 (0.04)
31 26 (1.022) X 12 (0.475) X 0.76 (0.03)
32 26.45 (1.044) X 8.35 (0.329) X 1 (0.04)
33 26.5 (1.045) X 13 (0.515) X 0.76 (0.03)
34 26.55 (1.045) X 15.65 (0.615) X 0.76 (0.03)
35 26.75 (1.05) X 17 (0.67) X 1 (0.04)
36 26.8 (1.055) X 12.75 (0.5) X 0.5 (0.02)
37 26.8 (1.055) X 9.6 (0.375) X 0.5 (0.02)
38 26.85 (1.055) X 12.65 (0.5) X 1 (0.04)
39 27.05 (1.065) X 8.3 (0.325) X 0.5 / 1 (0.020 / 0.04)
40 27.1 (1.066) X 13.85 (0.545) X 1 / 1.2 (0.04 / 0.047)
41 27.95 (1.1) X 15.65 (0.615) X 0.76 (0.03)
42 28 (1.1) X 10.9 (0.43) X 0.76 (0.03)
43 28.35 (1.115) X 18.9 (0.745) X 1 (0.04)
44 28.6 (1.125) X 10.9 (0.429) X 0.76 / 1 (0.03 / 0.04)
45 28.65 (1.13) X 21.05 (0.83) X 1 (0.04)
46 29 (1.14) X 8.6 (0.34) X 0.76 (0.03)
47 30.95 (1.22) X 21.6 (0.85) X 0.76 (0.03)
48 31 (1.22) X 8.9 (0.35) X 1 (0.04)
49 31.15 (1.225) X 17 (0.668) X 1 (0.04)
50 32.35 (1.275) X 8.25 (0.325) X 0.65 / 0.76 (0.025 / 0.03)
51 32.5 (1.28) X 24.55 (0.965) X 1 (0.04)
52 32.65 (1.285) X 17.1 (0.673) X 0.76 (0.03)
53 33.5 (1.32) X 18.05 (0.71) X 1 (0.04)
54 33.8 (1.33) X 9.5 (0.373) X 1 (0.04)
55 34.65 (1.365) X 19.45 (0.765) X 0.76 (0.03)
56 34.92 (1.376) X 20.26 (0.807) X 0.96 (0.037)
57 35.07 (1.376) X 15.5 (0.611) X 1 (0.04)
58 35.5 (1.4) X 25.75 (1.105) X 1 (0.04)
59 35.6 (1.4) X 8.7 (0.34) X 0.5 (0.02)
60 38.15 (1.5) X 14 (0.55) X 1 (0.04)
61 38.5 (1.515) X 24.1 (0.948) X 1 (0.04)
62 40.45 (1.59) X 21.05 (0.83) X 0.76 (0.03)
63 40.45 (1.59) X 13 (0.51) X 0.76 (0.03)
64 41.05 (1.62) X 16.35 (0.645) X 0.76 (0.03)
65 41.05 (1.62) X 12.55 (0.495) X 0.76 (0.03)
66 41.05 (1.62) X 10.1 (0.4) X 0.76 (0.03)
67 43 (1.695) X 16.25 (0.64) X 0.76 (0.03)
68 43 (1.695) X 12.15 (0.48) X 0.76 (0.03)
69 43 (1.695) X 10.35 (0.405) X 0.76 (0.03)
70 49.15 (1.935) X 20.35 (0.8 ) X 1.16 (0.045)
71 55 (2.165) X 20.05 (0.79) X 1.16 (0.045)
Thanx Bryan,
I plan on getting as much data into several spread sheets that I am working on and this is much appreciated.
Leo
Very good, thank you lots.... ;D
On your list you just have numbers by them. Do I just go to the smooth drags carbontex drag list and count down to number 47 for example and see what that washer is listed for? Thanks.
actually you look for the size CF washer you need and the corresponding number to the left is the part number. hope this is what you meant.
Aaron
The numbers are the size chart do not correspond to anything else :)
Just tried to keep it simple for ordering.
If you want to know what reel a particular washer belongs to just email and ask me.
Dawn
Quote from: Dawn on June 15, 2012, 03:57:27 PM
The numbers are the size chart do not correspond to anything else :)
Dawn
Dawn, i thought that was the purpose of the part numbering system to make life easier. for example if i wanted OD 21.28 mm ID 5.18 and 1 mm thickness i will order washer number 13, am i wrong?
thanks!
Mel you are right. I mis-understood what you meant.
OK here comes a dumb guy question...........I have a pile of Bass pro shop bait-casters......I know that they are made by several reel manufactures...can I get you bass pro #'s for proper CF washers????
fishnazzi, remember there are no dumb questions, only dumb answers.
dumb guy......thats me at times.........The drag washers on a couple of my reels are hammered. So I'm afraid trying measure the thickness of a hammered unit won't work.......and of course they are made by someone.......(the reels)......not sure about how to get the right sizes or if they are available........
Good question....but I don't have a good answer. Thickness is a game of chance. i just worked on a little shimano bass reel, and switched drags 3 times until I got the right thickness...how do I know? It was based on the star and how much drag I got based on the position of the star. If you get too much drag at the top, the washers are too thick. If bottoming out, too thin. Then I just try to find something in between...but I have a collection of washers to choose from and mix and match.
sounds like it might be easier to send the reels in............
You can send me the old washers if that's easier.
Dawn
That might work for me Dawn.....Thank You. It is summer season right now and work hours are long. But......in the fall........It is big fish time here. I will have to work at getting you some old ones(out of the reels) and in the mail.
The link to the PDF file on your website isn't working BUT, thanks to a little "sleuthing", here it is !
https://web.archive.org/web/20130702024204/http://www.smoothdrag.com/Carbontex_Sizes_2_rev6-2012.pdf (https://web.archive.org/web/20130702024204/http://www.smoothdrag.com/Carbontex_Sizes_2_rev6-2012.pdf)
this seems to be the latest list
Quote from: Wolli on October 21, 2016, 11:06:12 PM
this seems to be the latest list
Actually, there is a newer one . . .
LINK and PDF ( Attached )
http://smoothdrag.com/Carbontex_washer_sizes_Retail3-2014.pdf (http://smoothdrag.com/Carbontex_washer_sizes_Retail3-2014.pdf)Tight Lines !
DAIWA Saltiga Z4500
Bearing and CF washer dimensions
(original washers replaced with Smoothdrag CF washers!
hay brian i am looking to buy 6 #3 of your drag washers how do i order and pay for them
email bernard. houlihan@yahoo.com