hello there again..i just picked up a penn 700 greenie that ive almost completely disassembled ..the only problem im having is removing the handle from main gear..any tips on getting this handle loose without doing any damage...reel is in grate shape..wanna keep it that way...everything else apart and cleaned ..ready to put back together...just cant get that handle off...any replys appreciated Joe
Try replacing the pinion gear and rotor cup. Hold the rotor cup from turning locking the main gear. Try turning the handle loose remember it's a left hand thread so turn it clock wise. If still tight try heating the base of the handle with a heat gun and turn the handle assembly clock wise. The handle thread is 1/4-28 LH on the 712, 710, 704, & 700's.
Quote from: George6308 on March 03, 2019, 04:03:37 PM
Try replacing the pinion gear and rotor cup. Hold the rotor cup from turning locking the main gear. Try turning the handle loose remember it's a left hand thread so turn it clock wise.
Exactly what I was thinking. I always remove the handle
before pulling the rotor and pinion. 8)
Yes,
As George & Mike have pointed out — the crank handle should come off first before anything — right after removing the spool — so the rotor will hold the worm drive pinion steady and firm.
However, sometimes on these old salt-spinners — the crank will not always remove as we expect...
In those cases, and I have been known to insert a little wedge of hardwood between the main gear teeth and frame. And, it is always safer to remove the aluminum crank from the gear axle attachment part — then use a large handled screwdriver through the hole. That way, in case of a really stuck or fused crank — the softer aluminum handle will not be bent or snapped off.
Best,
Fred
slide the pinion back in, hold the flat part of the pinion where the nut goes on with a cresent wrench or any other wrench and un screw. harryk
believe me i did try to remove handle first thing..soaked with pb blaster for an hour b4 continuing on..2nd attempt with heat gun a success..thanks to all..Joe
Joe you are very welcome this site is always here to help
700 is a heavy but fun reel. By the way yours is the second version.
thanks for info george..picked up this 700 and a penn 249 in nice shape for 25.00..for the pair...got a picture of first version or how to tell apart..?...keep my eyes open
First generation has a cast green non folding handle and a die cast 43-700 crosswind arm. The rubber bail arm bumper is held in place by a spring and not a cup as on the later 704's.
That's quite an interesting heat gun! :)
use them guns for seaming rubber roofs..works wicked good..
Quote from: joe k on March 03, 2019, 06:00:08 PM
...Got a picture of first version or how to tell apart?
http://www.scottsbt.com/catalog/store/images/pennparts/information/spinfishers/Stick%27s%20Reel%20World%20--%20PENN%20SPINFISHER%20MUSEUM.htm :)
~
A~
Aiala..thanks for the sight..saved it..
Quote from: Aiala on March 03, 2019, 09:55:14 PM
Quote from: joe k on March 03, 2019, 06:00:08 PM
...Got a picture of first version or how to tell apart?
http://www.scottsbt.com/catalog/store/images/pennparts/information/spinfishers/Stick%27s%20Reel%20World%20--%20PENN%20SPINFISHER%20MUSEUM.htm :)
~A~
Thanks for posting that Aiala. I own a couple of 700's and have been over there looking for parts on several occasions. Never noticed that page. Very interesting.
Best,
Frank
Took some photographs of my restored Penn 700. It is painted the wrong shade of Penn green, the 700's were A darker shade from the factory.
Another part not showing is they used a Nice ball bearing. Nice's plant was across the street from Penn. You can see the cast 43-700 part and the spring holding the bail bumper.
Hey George...the past 3 greenies i got into..2 ..710s..1..700...all have Nice bearings in them... cleaned .reoiled.. working great.....i have 2 704 greens ..1 705..to get to ...all been in my archive for a while..starting to settle settle down and get into my collection from years past...never stopped buying penn reels when moment was right......spent lot of time on road with my job..
I believe was one of the first ball bearing companies to make miniature ball bearings. All made here in Philadelphia. Keep them oiled and they will hold up better than current Chinese one's. Nice's plant was on the corner of Hunting Park & Alleghany NW corner while Penn is on the SE corner.
The Greenis & "Z's" are like potato chips you "You cann't stop with one".