This gear set kit is ready for purchasing now.
This pinion gear will not work with any Tiburon spool without modify the spindle.
Order information:
1.) Send email to sales@prochallenger.com for requesting PayPal invoice, Please let me know if your order will be shipped within Florida when ordering
2.) Call 561-568-3980 by phone for using credit card. Please let me know if your order will be shipped within Florida when ordering
3.) Go to http://mkt.com/pro-challenger-llc (http://mkt.com/pro-challenger-llc) and place your order online (For US member only).
Here is the specification and price.
1.) 316 stainless steel main gear.
2.) 420 staineless steel heat treated pinion gear.
3.) Helical precision cutting.
4.) True 5:1 ratio
5.) Smooth spin pinion.
6.) Modified sleeve spacer.
7.) $47.99 (original) and $49.99 (custom).
This gear set will NOT work in Senator 112H. I am going to make some SS main gears as the original 4:1 Jigmaster.
There will be 6% sales tax for any order shipping within Florida state.
This Jigmaster 500/501 gear set kit is also available at Smoothdrag and Brian's Fishing Supply in Hawaii.
Thanks,
--Alan
(http://i1280.photobucket.com/albums/a494/prochallenger/DSC07107_zpsc6a55b8f.jpg?t=1408592709)
(http://i1280.photobucket.com/albums/a494/prochallenger/DSC07108_zpsfdf85514.jpg)
If they are the same price as the 113 set I will be open for 4 sets
Quote from: bluefish69 on March 19, 2013, 11:54:10 PM
If they are the same price as the 113 set I will be open for 4 sets
I will try to get around for $50.00 a set.
Alan, I'm in. They will be a good replacement for reels that I work on. Please note that the height will be of the 500 and not the 505...right?
Quote from: Bryan Young on March 20, 2013, 12:02:45 AM
Alan, I'm in. They will be a good replacement for reels that I work on. Please note that the height will be of the 500 and not the 505...right?
Hi B,
Yes, I know that, and the pinion diameter for the spool shaft should be little smaller than the 505. I did check with Alan T on it.
I was referring to the main gear height. Ill post pics of the difference...hopefully tonight.
Quote from: Bryan Young on March 20, 2013, 12:07:57 AM
I was referring to the main gear height. Ill post pics of the difference...hopefully tonight.
I know that. Don't worry.
I'm in for a set. I've got a set of accurate side plates that would love to be at 5:1. Thanks
Bob
Alan,
Count on 1 for starters (as you posted) and a few more if done right.
Thanks
Dom
I'm good for one set as well.
BINGO!
Put me down for a set!!!
Wayne
2 please
Put me down for 2 sets please Alan !
Thanks!
Put me down for 1 set please.
Ron
Put me down for a few, Alan. Don't forget about the 3.25:1 for the 6/0 ;).
Sal
I want one!
Put me down for one set please.
Thanks
William
Quote from: Alto Mare on March 20, 2013, 04:11:24 AM
Put me down for a few, Alan. Don't forget about the 3.25:1 for the 6/0 ;).
Sal
Hi Sal,
That 3.25:1 gear for 114H is on my to do list for the next project after this jigmaster 500.
Please put me in for one set Thanks doug
Put me down for 1 set Alan, and a 3.25:1 set for the 114H.
I'm in for a set, Alan. Bob
Quote from: Black Pearl on March 20, 2013, 08:53:58 PM
Quote from: Alto Mare on March 20, 2013, 04:11:24 AM
Put me down for a few, Alan. Don't forget about the 3.25:1 for the 6/0 ;).
Sal
Hi Sal,
That 3.25:1 gear for 114H is on my to do list for the next project after this jigmaster 500.
That's great news Alan, thank you!
Are the 4/0 gears on their way to me?
Quote from: Alto Mare on March 20, 2013, 09:31:04 PM
Quote from: Black Pearl on March 20, 2013, 08:53:58 PM
Quote from: Alto Mare on March 20, 2013, 04:11:24 AM
Put me down for a few, Alan. Don't forget about the 3.25:1 for the 6/0 ;).
Sal
Hi Sal,
That 3.25:1 gear for 114H is on my to do list for the next project after this jigmaster 500.
That's great news Alan, thank you!
Are the 4/0 gears on their way to me?
They are on the way to here from Tennessee. They should be here tomorrow, and I will ship it out to you. You should receive a payment email from PayPal later tonight.
Thanks,
--Alan
Payment sent!
Sal
Is it too late to add my name?
Quote from: raumati01 on March 22, 2013, 03:59:54 AM
Is it too late to add my name?
No, I am still taking name. This project has not started yet. It will be starting in about 3 weeks.
Look what they just came out with
http://www.ebay.com/itm/NEW-Tiburon-T3NK-30-Narrow-Topless-Kit-Penn-112H-Senator-30-WSB-Special-NEW-/121085237825
Alan, keep this project moving ;)
Gregg is a fine men to deal with, I've done lots of business with him.
Sal
Quote from: Alto Mare on March 23, 2013, 03:05:32 AM
Look what they just came out with
http://www.ebay.com/itm/NEW-Tiburon-T3NK-30-Narrow-Topless-Kit-Penn-112H-Senator-30-WSB-Special-NEW-/121085237825
Alan, keep this project moving ;)
Gregg is a fine men to deal with, I've done lots of business with him.
Sal
Hi Sal,
I believe that the 112Huse the same main and pinion as Jigmaster 500. Therefore, this project will be two birds in one stone.
Yes it does, that's why I said to keep it moving ;)
Quote from: Alto Mare on March 23, 2013, 03:05:32 AM
Look what they just came out with
http://www.ebay.com/itm/NEW-Tiburon-T3NK-30-Narrow-Topless-Kit-Penn-112H-Senator-30-WSB-Special-NEW-/121085237825
Alan, keep this project moving ;)
Gregg is a fine men to deal with, I've done lots of business with him.
Sal
I've been looking for one of these for a long time!!!!!! Thanks Sal.
Alan, I'd like 2 sets if they are still available.
Quote from: Jimmer on March 23, 2013, 01:27:32 PM
Alan, I'd like 2 sets if they are still available.
Hi Jimmer,
This project will start in 2 weeks.
Please add me in for 2 sets. Mahalo.
1 set for me please
Thanks
Greetings...this may be just what one of my customers is looking for....
Put me down for two sets.
Put me down for 1 set for now, more later.
I'm in for 1 set please.
Keith
Alan, can you put me down for 1 set?
Thanks
Peter
put me down for 2 sets, thanks!
I'm in for 2 sets.
I'll take a set if $ is right
I would like one too if they are still available? Thanks, Andrew
3 sets for me please.
Simon.
If I can get in... one set please, but two if available
Thanks, Bile
I'll take a set for my ProGear 255.
Hi Alan,
Please put me down for 1 set.
Thanks!
David
I'll be in for a couple of sets. 8)
2 sets please. Mahalo from Hawaii.
Mark
Just to clarify,
The proposed gear set is similar to this:
(http://i986.photobucket.com/albums/ae348/hawaiiansurfinboy/AlanTani/500gearset_zps01b16d11.jpg) (http://s986.photobucket.com/user/hawaiiansurfinboy/media/AlanTani/500gearset_zps01b16d11.jpg.html)
I proposed to Alan that the area where the drags sit should be deeper to allow a 5 CF drag stack as:
(http://i986.photobucket.com/albums/ae348/hawaiiansurfinboy/AlanTani/Proposed500gearset_zps0c06d846.jpg) (http://s986.photobucket.com/user/hawaiiansurfinboy/media/AlanTani/Proposed500gearset_zps0c06d846.jpg.html)
based on my conversation with Gene. What do you guys think?
That will be a customize gear. It will be for this site only. I will have to have 50 sets to make this special gear happens. Quote from: Bryan Young on April 16, 2013, 08:14:59 PM
Just to clarify,
The proposed gear set is similar to this:
(http://i986.photobucket.com/albums/ae348/hawaiiansurfinboy/AlanTani/500gearset_zps01b16d11.jpg) (http://s986.photobucket.com/user/hawaiiansurfinboy/media/AlanTani/500gearset_zps01b16d11.jpg.html)
I proposed to Alan that the area where the drags sit should be deeper to allow a 5 CF drag stack as:
(http://i986.photobucket.com/albums/ae348/hawaiiansurfinboy/AlanTani/Proposed500gearset_zps0c06d846.jpg) (http://s986.photobucket.com/user/hawaiiansurfinboy/media/AlanTani/Proposed500gearset_zps0c06d846.jpg.html)
based on my conversation with Gene. What do you guys think?
Alan, you know I'm good for two sets.
Bob
I personally would rather have the hex gear. The drag range for 5+1 carbontex or hex HT-100 are comperable and the HT-100 is cheaper and more available.
Ron
I think we need a new thread for this customize gear set. What do you think?
If this will be a customized gear set, it's not worth it guys. Just a suggestion for the gear set offered that way you have an option of a 3 stack or 5 stack.
I'm in for two sets if they will fit the 505. Cheers neal.
Quote from: WTFOBaja on April 23, 2013, 05:02:28 AM
I'm in for two sets if they will fit the 505. Cheers neal.
Hi Neal,
This will not fit JigMaster 505. The 505 is already 5:1 ratio, but it is not in stainless steel.
Thanks,
--Alan
Quote from: Black Pearl on April 23, 2013, 04:30:52 PM
Quote from: WTFOBaja on April 23, 2013, 05:02:28 AM
I'm in for two sets if they will fit the 505. Cheers neal.
Hi Neal,
This will not fit JigMaster 505. The 505 is already 5:1 ratio, but it is not in stainless steel.
Thanks,
--Alan
Hi Alan,
What pattern did you use as a reference? Newell gears, Penn Gears, Accurate Gears, or on of your own design?
Neal, the main gear will fit. The pinion, I cannot remember, was the 500/501 ID larger than the 505/506? If it's larger, then it would work. If it's smaller, then you will need to boar it out and then it would work.
By the way, what is the ETA on the gears?
Bryan
The 500 jigmaster pinion gear will fit the 505. Its a little lose on the spool shaft, but definitely usable. I like mine tight though.
The main gear is the same.
You could also make the 505 pinion work in a 500, by making some little modifications.
We like modifications around here, Neal, as you'll find out soon enough ;D
enjoy your stay, by the way.
Sal
Quote from: Bryan Young on April 23, 2013, 05:51:27 PM
Quote from: Black Pearl on April 23, 2013, 04:30:52 PM
Quote from: WTFOBaja on April 23, 2013, 05:02:28 AM
I'm in for two sets if they will fit the 505. Cheers neal.
Hi Neal,
This will not fit JigMaster 505. The 505 is already 5:1 ratio, but it is not in stainless steel.
Thanks,
--Alan
Hi Alan,
What pattern did you use as a reference? Newell gears, Penn Gears, Accurate Gears, or on of your own design?
Neal, the main gear will fit. The pinion, I cannot remember, was the 500/501 ID larger than the 505/506? If it's larger, then it would work. If it's smaller, then you will need to boar it out and then it would work.
By the way, what is the ETA on the gears?
Bryan
Hi Bryan,
We will use the 505 as a reference to make it fit with 500/501. The 500/501 pinion ID is lager than 505. Currently, the resource is doing the mass production of the 113H, and he is working on the 114H. Then, it will be the 500/501.
My resource does not like to rush into anything because he always wants to make sure his workmanship is prefect before anything else.
Probably not with the metal washers that are available. We would need to go to a thinner material and if that, a stronger and therefore more expensive material. I will talk with Lee if he can get some cut.
Thank you to sal and bryan for the info. I am still in for two sets and i'll give the 500 pinion a shot. Neal.
I would like a set for the 500 and the 4/0
I would like two sets.
John
One set for my 112h, please...and so it begins ;D
I'll start with 2 sets.
Alan,
I'd prefer the 5 stack over the 3 stack if they come to fruition. If you're making the customized gear I'll take those... if you don't I'll take the regular 3 stack.
Thanks
Dom
Quote from: broadway on May 29, 2013, 12:52:19 AM
Alan,
I'd prefer the 5 stack over the 3 stack if they come to fruition. If you're making the customized gear I'll take those... if you don't I'll take the regular 3 stack.
Thanks
Dom
Dom,
5 stacks was supposed to be a secret. :)
We don't have any secrets around here ;).
I just said, "IF" you're making them ;)
Quote from: Black Pearl on May 29, 2013, 01:06:27 AM
Quote from: broadway on May 29, 2013, 12:52:19 AM
Alan,
I'd prefer the 5 stack over the 3 stack if they come to fruition. If you're making the customized gear I'll take those... if you don't I'll take the regular 3 stack.
Thanks
Dom
Dom,
5 stacks was supposed to be a secret. :)
Now you've done it, Dom. :D
I want 2 sets of the SECRET gears ;D
Not to hijack this thread, but I'm working on a 5+1 carbon fiber plus metal washers drag kit that will fit the normal Jigmaster 500/501 and Penn 112H gearset. We just got the materials and are going to the cutter today. We are cutting 100 sets. We will soon try them out on older steel gears and a new brass gear set to see how they do. I'm hoping for a solid 15# of drag with max of 20# given the ears on the drag set doesn't give our or the gears strip out. Will keep you guys advised.
Hey bryan, sounds very exciting. Will the falt washers fit inside the hex drop-in that Keta made?
Bob
No they won't. This set will be like what is in the reel already but will see if we can fit 10 washers in the gear instead of 6 (5 metal and 5 carbon fiber).
So theoretically #25 of drag right? Nice!
Quote from: BMITCH on May 30, 2013, 07:52:14 PM
So theoretically #25 of drag right? Nice!
Theoretically, yes, but those drag ranges will be at your risk. I'm more talking reasonable drag range that will not damage the reel.
Bryan,
If it works as you plan count me in for 5 sets... I've been using my 112H for striper fishing lately and would love to set them up for wireline as well. I've tried the 112h hot rodded to the nines, but I just don't have the drag range. When I put on the umbrella rigs they take a little line out on turns because the drag isn't there.
Keep us posted on the progress,
Dom
Bryan, sounds good. If you get it going I'd take three sets when they become available.
Thanks, Bob
Alan: Don't forget my set LOL
Gene
Hi all,
As many of you know that Dawn from Smooth Drag is coming out with the Newell gear set, which can fit PENN 112H or JM 500/501.
Smooth Drag gear set is made in the USA, and it is only $35.00 a set. I believe that it is a good price for a gear set that is made in SS 304.
I will still process my JM 500 gear set in SS 316 project with couple features (those features are from Dom (boardway)). I can't state what those features are. When it comes out, I will state those features.
If any member wants to cancel his order on my PENN 500 gear set, please post it here.
Thank you all.
Thanks,
--Alan
Alan,
I will hold off on purchasing anything until I see your gears or you release what the features are. You two have saved the world!!
Ron
I am going to roll the dice and assume that whatever you and DOm have cooking will be worth it. At the least be a limited edition collectors item that will be worth a fortune one day and pay for my son's tuition (no pressure guys)
I'm ALL over this. I'm in with these and the one Dawn is bringing out. I figure I can have a drag stack of cf washers ready to go in these and instead of having to clean old grease off the gears I can just pop in a new set per-loaded with the drag washers. ;D ;D ;D. I've got a couple buddies with 500's that now I know what to get them for their birthday, Christmas...etc.
Bob
My Grandson's Birthday is in August & my Birthday is in Sept. Well that's 2 less sets I have to buy.
Mike
I still want one of your sets. I am confident that I'll be happy
Hi all,
How are you all? Here is the latest info I have for this JigMaster 500 high speed gear project.
After few weeks of continuous R&D on this gear set, I am very happy to inform you all that we have achieved to make few adjustments to make this gear set in true 5.0:1 with helical cutting. My guys are busy testing its strength under stress and making sure the main or pinion gear will not round off. So far, it looks very promising.
It might take another month or so to have the first 15 sets available, and 3 or 4 months before the second batch gear sets are available.
If any of you really need this JM 500 gear set in hurry, you can check out Smooth Drag's on its JM 500 gear set (http://alantani.com/index.php?topic=7440.0 (http://alantani.com/index.php?topic=7440.0)).
If anyone is no longer interested in my JM 500 gear set, and your name is on this thread, please let me know that you would like to cancel the order. Therefore, I won't bug you when the order is ready to be shipped.
Thanks,
--Alan
Hi Alan, I'm very excited to get one of these to start. I see you will only be making 15 sets to start with. I will need a total of 3 sets but would like only one to start and will wait for the other two when the mass production starts. Just want everyone to get a crack at these. Let me know and thanks for the update.
Bob
Hi Alan,
I'm with Bob on that.... I'm still in for my 2 sets, but would take only 1 on the first round to allow the first 15 to spread out....
That's IF my order is up there in the 1st 15... ;)
Thanks for all your efforts buddy... nice chatting with you last week!
Erik
Fiji
Alan
I will take 1 set at the beginning just for show & tell class. I will be happy to wait for the other 3 sets. All 4 sets are only spares anyway.
Mike
I'm still in. Bob
put me down for one set
I bought a 112HN frame and spool. I'm definitely in now! Any idea when the gears will be ready? ;D
Quote from: floating doc on June 24, 2013, 06:04:32 PM
I bought a 112HN frame and spool. I'm definitely in now! Any idea when the gears will be ready? ;D
Hi,
We just finished up the 114H first 20 sets. We are going to start making the initial testing JM 500/ 112H gear set. If everything is turning out perfect, we will start the first 20 sets 112H first. It will be a month before I will have the first 20 set batch.
If you can not wait for that long, you might want to check with Dawn at Smooth Drag if she has the 112H from her resource ready to go.
Thanks,
--Alan
I'm still in, and could probaly take a 3rd set. Can't wait. Fun stuff!
This reminds me of the old ketchup commercial...............anticipation. I can hear Carly Simon's voice.
Hey Alan,
Put me on the list for 1 gearset.
Thanks,
Max
If you can not wait for that long, you might want to check with Dawn at Smooth Drag if she has the 112H from her resource ready to go.
Thanks,
--Alan
[/quote]
I'm going to wait for the Black Pearl set, but thanks for the referral. I'm slowly accumulating parts; I have my donor reel and the frame/spool. The drag set arrived today.
I will take one set out18
How your time frame Alan? Leaving on the 8/18 for a 6 day. I got a chance to use the 4:1 gears in my ProGear 545 worked great nice & smooth.
Quote from: lasparky11 on July 18, 2013, 05:08:33 AM
How your time frame Alan? Leaving on the 8/18 for a 6 day. I got a chance to use the 4:1 gears in my ProGear 545 worked great nice & smooth.
Hi there,
I don't think I will be able to make it on that date. We are taking little more time on the pinion gear because it requires a very precision cutting on it. My guys are working very hard to try to make it 99.9% prefect for a true 5:1 gear set. The earliest for the first 20 sets will be around the end of August. Please note that there will be 2 model (original and an extra 1mm mills in the main gear) on this JM 500 gear set.
You know my gear set is good and smooth like silk.
Did you know that the 114H gear we just made was so smooth and quiet that you won't even know it has gear in the reel?
hi alan,
what's approximate due date for penn 500 gear set? i'd like to get the gears with drag set and ss sleeves.
thanks ralph
Quote from: thinket on August 24, 2013, 05:52:02 PM
hi alan,
what's approximate due date for penn 500 gear set? i'd like to get the gears with drag set and ss sleeves.
thanks ralph
Hi Ralph,
I will have the first 20 sets (15 original and 5 custom) available very soon. My resource is testing the teeth strength on the gear because we are making it in true 5:1 ratio.
If you have any questions, please feel free to PM me.
Thanks,
--Alan
I need two Alan. Thanks!
Gulf red snapper will have a special season starting October first. I'm going to be in Destin. I'll start building my jigging rod.
Great timing!
Quote from: floating doc on August 27, 2013, 06:19:52 PM
Gulf red snapper will have a special season starting October first. I'm going to be in Destin. I'll start building my jigging rod.
Great timing!
Please note that the first 20 sets will be available next month, but the mass production will be around end of Nov or early Dec.
Hi Alan,
Can I get 1 of each set for drag fitment? Then I can send them to whomever wants them...I can wait. I just want them to make sure I can have a drag set for them.
Bryan
Quote from: Bryan Young on August 28, 2013, 07:34:51 PM
Hi Alan,
Can I get 1 of each set for drag fitment? Then I can send them to whomever wants them...I can wait. I just want them to make sure I can have a drag set for them.
Bryan
I will let you know when I have them.
Red Snapper opens in the Gulf of Mexico October first. How's it look for mid September?
I just got a confirmation on the first 20 sets will be finished by mid-Sept, then I will have them a week later by mail.
Here is the specification and price.
1.) 316 stainless steel.
2.) Helical precision cutting.
3.) True 5:1 ratio
4.) Smooth spin pinion.
5.) $46.99 (original) and $49.99 (custom).
For the first 20 sets (15 original and 5 custom) will be sold as above price.
For member who can wait for the mass production run (Dec 2013), the price will be $42.99 (original) and $45.99 (custom) each set.
Please let me know who want to have one set from the first 20 sets (1 per member). That will be first comes first serve.
1.) Alto Mare - custom (1)
2.) Broadway - custom (1)
3.) BMITCH - custom (1)
4.) El Pescador - custom (1)
5.) Bryan Young - custom (1), Original (1) :D
I should be on list for original.
If I remember correctly, the custom sets were for a hexagonal type drag?
If so,
I already have a 5/1 drag set. Definitely put me down for the first run.
Quote from: floating doc on August 29, 2013, 11:06:48 PM
If I remember correctly, the custom sets were for a hexagonal type drag?
If so,
I already have a 5/1 drag set. Definitely put me down for the first run.
The custom is not HEX. HEX is only in 114H and 115L.
For more info on the custom 112H/JM500 gear, please check with Bryan Young.
The first 5 custom gear are gone.
I added me to the list. :D I hope they are available for me.
Quote from: erikpowell on March 20, 2013, 02:46:38 AM
Put me down for 2 sets please Alan !
Thanks!
Hi Alan, I'd like to have at least one from this run if you still have some left...i can wait for the production run for the 2nd set.
p.m. me with details...Thanks a lot
Erik
Is the availability for the original sets going in order of requests according to this thread?
Quote from: mbg60 on August 31, 2013, 04:52:52 PM
Is the availability for the original sets going in order of requests according to this thread?
I hope so. I've been holding out for these.
I would like one set of the custom gears from the production run.
Rob
Quote from: mbg60 on August 31, 2013, 04:52:52 PM
Is the availability for the original sets going in order of requests according to this thread?
Yes, but some members don't want to pay the full price, and they want to wait for the mass production run (save money).
BP
I told you in the beginning that I was not in a rush for the gear sets & it has nothing to do with the price. At this time I have been doing Daiwa Reels mostly 27H & 50 H. The 50 H is a true workhorse of a reel.
I still want the 4 Gear Sets that I asked for but not now. When the full run comes in let me know.
Mike
Quote from: Black Pearl on September 02, 2013, 01:31:15 AM
Quote from: mbg60 on August 31, 2013, 04:52:52 PM
Is the availability for the original sets going in order of requests according to this thread?
Yes, but some members don't want to pay the full price, and they want to wait for the mass production run (save money).
I'm ok with full price; I'm going to have my yearly pilgrimage to Destin, FL for a special red snapper season next month.
Just remind me, please: what's the difference in the custom gears?
BP
I'm still in for one set from the first run if there are any left. I'll wait for the second run for the other set.
Just an idea would anyone else be into a stainless gear for the 140?
Thanks neal.
I'm down for 1 from the original run if you still got them.
I'm in if there are still some hanging around.
I would like 2 ea
Hi guys,
I know that a lot of people are waiting on this Jigmaster 500/112H gear sets. My factory is working tirelessly. As you all know that the Jigmaster 500/112H gears (main and pinion) are very small, and there is not really a lot of room to make it 5:1 ratio, but we are making it. We have to make sure 100% that every sets is clean, work well with other parts of the reel, and good strength on all gear teeth. Therefore, it might take couple more weeks. We don't want to rush it too fast and bring out any crappy gear sets.
I can guarantee that any gear set I am going to sell or am selling, it will be the best in the market right now.
Sorry for the delay guys.....
Thanks,
--Alan
How's that go? "You can't rush perfection. "
I'm good with that.
Roger that BP. You created a market for your product. High demand!
Are there any of these sets still available from the 1st run and if so,where do I send $?
Quote from: bigcatpat on September 18, 2013, 04:50:14 AM
Are there any of these sets still available from the 1st run and if so,where do I send $?
We are still working on its improvement at this moment. We should have the first 20 sets done very soon.
No money will need to be sent to us yet because we don't have the gear set on hand yet. I am not a believer on keeping other people's money on hand while they are waiting for my product.
Thanks,
--Alan
Finally, the JigMaster 500/501 or PENN 112H true 5:1 gear set (20 sets) will be in FL by the end of next week. Here is a picture of it.
Please note that the pinion does not have the ring on in the picture. Don't worry, it will be on it.
My resource has been testing it. This gear is much stronger and smoother than the Accurate gear set.
Enjoy!!!!
(http://i1280.photobucket.com/albums/a494/prochallenger/1a64d2e0-c5c2-45ea-b64d-b95269b0c2fa_zps85dfce80.jpg)
hey alan c.! am i on the first 20 list? ;D
:D
Looks like a winner!
Very, Very nice Alan. I cant wait. ;D
Bob
Will these fit the 505 and 506?
These should fit the Penn 505 and 506. The difference is that you will have greater space between the sideplate and the gear. You may need to fill it with an extra washer.
I want a set please.
Alan,
If there is any left from the first run I would like to get a set If not when will the second run commence?
Thanks,
Quote from: maxpowers on September 28, 2013, 08:29:07 PM
Alan,
If there is any left from the first run I would like to get a set If not when will the second run commence?
Thanks,
So far, I don't know if there is any left from the first run (20 sets). I will have better idea after I receive the shipment. If a person I send a pm to, and he does not reply within 3 days, then I will post it here and let everybody knows how many I have left on hand. It will be first come first server at that time.
Quote from: Bryan Young on September 27, 2013, 10:25:28 PM
These should fit the Penn 505 and 506. The difference is that you will have greater space between the sideplate and the gear. You may need to fill it with an extra washer.
Bryan,
regarding the fitment, will the pinion fit and when you mentioned that washer is needed where would it goes? Do you meant in the drag stack?
I'm only speaking of the main gear. I'm not sure of the pinion fitment as I am not aware of the design constraints.
Quote from: maxpowers on October 02, 2013, 06:03:59 AM
Quote from: Bryan Young on September 27, 2013, 10:25:28 PM
These should fit the Penn 505 and 506. The difference is that you will have greater space between the sideplate and the gear. You may need to fill it with an extra washer.
Bryan,
regarding the fitment, will the pinion fit and when you mentioned that washer is needed where would it goes? Do you meant in the drag stack?
This Jigmaster 500/501 will not work on 505/506 at all because the ID diameter is not the same as 505/506.
Here it goes again.
There are only 18 sets available, and they are on their way to FL right now.
Please note that there are 10 sets custom gear sets (it milled 1mm deeper inside the main gear), and there are 8 sets regular.
I will send out an email to some members on their order. One set per member on the this first run sample sets.
Thanks,
--Alan
Alan,
I am almost certain that the 505/506 use the same drag washers, these gears should fit. The factory gear sleve has a different thread pitch but the diameter is the same. I think the pinion might need a little work but it should not be a big deal.
Of course, I could be out to lunch. ;D
Ron
Quote from: noyb72 on October 03, 2013, 06:50:07 PM
Alan,
I am almost certain that the 505/506 use the same drag washers, these gears should fit. The factory gear sleve has a different thread pitch but the diameter is the same. I think the pinion might need a little work but it should not be a big deal.
Of course, I could be out to lunch. ;D
Ron
I believe that the 500 ID pinion (spool shaft hole) is smaller than the 505. Therefore, my pinion gear will not fit the 505 spool shaft.
Quote from: Black Pearl on October 03, 2013, 07:00:42 PM
Quote from: noyb72 on October 03, 2013, 06:50:07 PM
Alan,
I am almost certain that the 505/506 use the same drag washers, these gears should fit. The factory gear sleve has a different thread pitch but the diameter is the same. I think the pinion might need a little work but it should not be a big deal.
Of course, I could be out to lunch. ;D
Ron
I believe that the 500 ID pinion (spool shaft hole) is smaller than the 505. Therefore, my pinion gear will not fit the 505 spool shaft.
Yes, but the other way around ;D. These Jigmaster 500 gears should work nicely in the 505/506.
The pinion is usually a little loose, but from knowing the way your machinist cuts these gears, I believe they will be almost perfect ....very little movement on the 505/506.
bottom line; the 500 gear set will work on the 505/506.
Those 18 gear sets will be here on Monday.
Please send me a PM or email if you want to know if your name is on my list and let me know if your order is for original or custom main gear.
Guys, I can't wait to see these gears. My guys told me that it is amazing smooth, quiet and great strength. I guess that it is worth to wait and make sure everything is prefect......
Thanks guys,
--Alan
Do I need to refresh your memory? ::)
Quote from: Alto Mare on October 04, 2013, 06:22:52 PM
Do I need to refresh your memory? ::)
Yeah, I know you always want the custom one. ;)
Quote from: Black Pearl on October 04, 2013, 09:16:26 PM
Quote from: Alto Mare on October 04, 2013, 06:22:52 PM
Do I need to refresh your memory? ::)
Yeah, I know you always want the custom one. ;)
Correction: I like the custom ones
Couple sets have been sent to Sal for checking.
Here are some pictures.
(http://i1280.photobucket.com/albums/a494/prochallenger/DSC06907_zps6c5ba89e.jpg)
(http://i1280.photobucket.com/albums/a494/prochallenger/DSC06909_zpsb844edf4.jpg)
(http://i1280.photobucket.com/albums/a494/prochallenger/DSC06911_zps9004a521.jpg)
(http://i1280.photobucket.com/albums/a494/prochallenger/DSC06912_zpsa67ca8ae.jpg)
(http://i1280.photobucket.com/albums/a494/prochallenger/DSC06915_zpsef30056d.jpg)
(http://i1280.photobucket.com/albums/a494/prochallenger/DSC06916_zpsd513af26.jpg)
Hi Alan,
I would like 2 sets if available from the first run. If not could you put me on the list for the second run?
Thanks,
Here is the mini written up for this 500, 505 0r 112H gear set.
http://alantani.com/index.php?topic=8592.0 (http://alantani.com/index.php?topic=8592.0)
Quote from: Black Pearl on March 19, 2013, 11:49:35 PM
Hi guys,
For member who is waiting for the mass production run (Dec 2013), the price will be $42.99 (original) and $45.99 (custom) each set until 11/15/2013.
I will offer this price to Alan Tani's website USA member only.
If you are interested, please add your name in this thread.
Thanks,
--Alan
I will buy 2 sets from production run of original/standard.
Hi guys,
Just a reminder, if you are buying the custom gear, which is deeper, it was designed so that you could purchase SmoothDrag's SS metal washer set of 5 washers plus the Daiwa Million Carbontex Kit and have a 5+1 stack in your Penn 500. This was designed way before I developed the my drag set.
Bryan
Or where the Belleville rubs on the plate.
Hi,
I have 3 sets custom gear left. If you want it, please let me know.
Thanks,
--Alan
Please note that a stainless steel yoke will require to install this stainless steel gear set.
Does this apply to both the original AND custom gears?
Quote from: mbg60 on October 14, 2013, 06:37:55 PM
Does this apply to both the original AND custom gears?
Yes, because the 316 stainless steel will eat up the brass yoke, and it will make a mess.
Personally, I'd fish it until it needed replacing, but that's just me.
Quote from: Bryan Young on October 14, 2013, 07:42:23 PM
Personally, I'd fish it until it needed replacing, but that's just me.
I know that brass is soft, but l don't know about filling the reel with the brass shavings as the yoke wears away.
Doc
The S S Yokes are $4 ea
Mike
Quote from: Black Pearl on October 13, 2013, 02:45:58 PM
Hi,
I have 3 sets custom gear left. If you want it, please let me know.
Thanks,
--Alan
Here is an update on this gear set I have on hand.
Custom gear set: None available. Waiting for 2 1 members' payment.Original gear set: 1 0 available. Waiting for 2 1 member's payment.Please note that if I do not receive the payment from the member within 3 days after the invoice date, that invoice will be cancel.All gear sets are all sold....
Quote from: Black Pearl on October 15, 2013, 02:21:10 PM
Quote from: Black Pearl on October 13, 2013, 02:45:58 PM
Hi,
I have 3 sets custom gear left. If you want it, please let me know.
Thanks,
--Alan
Here is an update on this gear set I have on hand.
It's good to see that they sold fast. I want to see the Black Pearl gears become established as the ultimate upgrade.
I'm glad they sold fast. I want to see these gears in a lot of reels.
Custom gear set: None available. Waiting for 2 1 members' payment.
Original gear set: 1 0 available. Waiting for 2 1 member's payment.
Please note that if I do not receive the payment from the member within 3 days after the invoice date, that invoice will be cancel.
All gear sets are all sold....
Alan, what's the time frame on the next run of gears?
Thanks Peter
Quote from: p-deverett on October 16, 2013, 07:18:24 AM
Alan, what's the time frame on the next run of gears?
Thanks Peter
Hi Peter,
The mass production should be ready by end of Dec.
Thanks,
--Alan
Alan, do we need to pre-order on these sets slated for the end of Dec.? If so will the "special" deeper ones be available at that time?
Thanks,
Bob
Quote from: BMITCH on October 16, 2013, 03:56:35 PM
Alan, do we need to pre-order on these sets slated for the end of Dec.? If so will the "special" deeper ones be available at that time?
Thanks,
Bob
Hi Bob,
No, there will be enough to go around (I hope).
Alan, please put me down for 3 sets on the next run. Thanks!
Alan, just a reminder i'm in for a couple of sets and could pick up some more if you get stuck with'em. I've got plenty of old Accurate Conversions I would like to upgrade.
Thanks.
installed mine last Tuesday perfect fit. now can`t wait to install the 4/0 on my PG541 when I get back to brasil. yeah hey! what`s next Alan C.?
Quote from: Mel B on October 17, 2013, 03:36:43 PM
installed mine last Tuesday perfect fit. now can`t wait to install the 4/0 on my PG541 when I get back to brasil. yeah hey! what`s next Alan C.?
Mel, you know what is the next sample gear set will be. ;)
Quote from: Black Pearl on October 19, 2013, 02:40:59 PM
Quote from: Mel B on October 17, 2013, 03:36:43 PM
installed mine last Tuesday perfect fit. now can`t wait to install the 4/0 on my PG541 when I get back to brasil. yeah hey! what`s next Alan C.?
Mel, you know what is the next sample gear set will be. ;)
Mr. Chui, don't reveal my secrets ;) ;D.
So there is no plan to produce gear sets for the Penn 505/506 models?
Quote from: BonitaBch on October 22, 2013, 03:33:44 PM
So there is no plan to produce gear sets for the Penn 505/506 models?
According to Sal, this gear set will work on the Jigmaster 505/506. Please see the following thread.
http://alantani.com/index.php?topic=8592.0 (http://alantani.com/index.php?topic=8592.0)
Well,i'll be needing 4 sets now that I know they'll fit my 505,s. :)
Quote from: bluefish69 on October 15, 2013, 02:37:24 AM
Doc
The S S Yokes are $4 ea
Mike
Could you tell me where to purchase the SS yokes? Can anyone tell me if the yoke is the same on the JM 500 and the JM 505HS?Thanks
Quote from: bigcatpat on November 17, 2013, 05:22:22 AM
Quote from: bluefish69 on October 15, 2013, 02:37:24 AM
Doc
The S S Yokes are $4 ea
Mike
Could you tell me where to purchase the SS yokes? Can anyone tell me if the yoke is the same on the JM 500 and the JM 505HS?Thanks
Doc,
Please have a look at the following thread in this site.
http://alantani.com/index.php?topic=8737.0 (http://alantani.com/index.php?topic=8737.0)
Alan, When you get them in please put me down for 1 set. Thanks! 8)
Hey Alan,
I'll take 4 sets please.
Alan
Put me down for 4 sets
Mike
Alan,
I will need 3 sets.
Thanks
Here is an updated.
Sal tested the latest gear set in the 112H, and it did not do good, but it did really good in the Jigmaster 500/501. So, this 5:1 gear set will NOT work in the Senator 112H.
However, I am going to make few main gear in 4:1 ratio (as same as the main gear uses in the 112H or Jigmaster) in stainless steel. It will work with original 4:1 pinion gear by PENN.
Sal, can you post the test result on the 5:1 gear set, please?
Thanks,
--Alan
Soooo, does this mean we can p.m. you for our orders?
Quote from: Black Pearl on May 22, 2014, 02:15:44 AM
Here is an updated.
Sal tested the latest gear set in the 112H, and it did not do good, but it did really good in the Jigmaster 500/501. So, this 5:1 gear set will NOT work in the Senator 112H.
However, I am going to make few main gear in 4:1 ratio (as same as the main gear uses in the 112H or Jigmaster) in stainless steel. It will work with original 4:1 pinion gear by PENN.
Sal, can you post the test result on the 5:1 gear set, please?
Thanks,
--Alan
Works for me. Actually, I would prefer the 4:1 gear for my 112h. But I've got two jigmasters and the 112h sitting here with all the available upgrades just waiting for a set of SS gears so I can complete this project. (getting antsy I guess).
All due respect to Sal and Alan, I know they've put in a lot of time and effort to try and make this thing work, and I appreciate that. But there is simply no way I'm going to push these reels to 20lbs. of drag in a normal every day fishing situation. More like 10-12 lbs. tops. If I need 15-20 lbs., I've got reels for that.
Again, thanks for the effort guys, but you've already exceeded my expectations.
Ed
Yes you're right Ed, there are reels out there that will get you to 20lb, this isn't for everyone. The Jigmaster was already a nice reel , it is now a much better reel. I personally like what we've done very much.
Sal
I have to agree with this. In fact, I's say these are still fine in the 112H under reasonable drag levels. I have seen several references of the new 112HN Tib kit being called the White Sea Bass special. I caught my first WSB about 30 years ago and have hooked into many, many fish since then. They are an absolute blast to katch but they do not require 25#s of drag. I have caught lots of legal fish with a Mitchel 300 and a size 4 hook! They do however, like to run at you and that means you need to get line in fast. For the WSB application when fighting WSB I'd say the 5:1 gear ratio is more important than mamoth drag numbers.
Well done to all.
Ron
I just built a 112H with original steel main gear and Bryan's 5 stack washers. I got the .5mm drag washers from Dawn. I was out of that material.
The little reel pulled 28 lbs. of smooth drag. I was truly amazed. I have 2 sets of the eBay SS gear sets but I don't think they will hold up so I didn't use them.
It's for a customer that loves these little reels and I might have to get one myself to prove to my Avet loving son what they will do..!!
Hey Alan,
I'll take 1 set please.
Marc..
Quote from: Marcq on July 17, 2014, 05:27:21 PM
Hey Alan,
I'll take 1 set please.
Marc..
Hi Marc,
This gear set kit will fit Jigmaster only. The gear set kit will be ready by end of this month.
Thanks,
--Alan
10-4
Thanks, Marc..
Sign me up for a set! ;D
When can we order???????
Quote from: bigcatpat on August 01, 2014, 02:21:42 AM
When can we order???????
The Jigmaster 5:1 gear set kit will ship out to the US on Monday 08/4/2014. To place your order, please send email to sales@prochallenger.com or call 561-568-3980 by phone.
Thanks!!! I'll be calling you today!!!+ ;D ;D ;D 8) 8) 8)
I sent you an order at the sales@prochallenger.com address.I put my paypal address on there. 8) 8) 8) If I need any of those extra washers you were talking about please include those in the order too.I am going to be using Bryan's drag stack too.
Quote from: bigcatpat on August 03, 2014, 12:47:20 AM
I sent you an order at the sales@prochallenger.com address.I put my paypal address on there. 8) 8) 8) If I need any of those extra washers you were talking about please include those in the order too.I am going to be using Bryan's drag stack too.
Hello Bigcatpat, Alan Chui will send you the main gear the pinion and the spacer, anything else you will need to get on your own. If you're using these gears in your 505, you might need another metal washer or two on top of the stack.
This is not a big deal, you could use the older metal washers on top or some from Bryan..
How you like your drag it's up to you, most of my reels start very soft, cranking the handle doesn't move the spool when the star is backed all the way.
Some like to set theirs differently, they do want a little drag at first, when the star backed all the way.
Sal
Quote from: Alto Mare on August 04, 2014, 09:18:51 PM
Quote from: bigcatpat on August 03, 2014, 12:47:20 AM
I sent you an order at the sales@prochallenger.com address.I put my paypal address on there. 8) 8) 8) If I need any of those extra washers you were talking about please include those in the order too.I am going to be using Bryan's drag stack too.
Hello Bigcatpat, Alan Chui will send you the main gear the pinion and the spacer, anything else you will need to get on your own. If you're using these gears in your 505, you might need another metal washer or two on top of the stack.
This is not a big deal, you could use the older metal washers on top or some from Bryan..
How you like your drag it's up to you, most of my reels start very soft, cranking the handle doesn't move the spool when the star is backed all the way.
Some like to set theirs differently, they do want a little drag at first, when the star backed all the way.
Sal
Thank you very much Sal!!!! 8)
Alan,please check your pm's.I sent you an order. :)
Quote from: bigcatpat on August 05, 2014, 02:28:33 AM
Alan,please check your pm's.I sent you an order. :)
[/qute] Did you check your PM's yet Alan?
Hi guys,
I have received a lot of emails on the Jigmaster 5:1 gear set kit.
I have not received the shipment yet. I know that the 9/0 pinion gears are done for the past 2 weeks, and the Jigmaster's main, pinion gears are done last week. At the final stage, while testing the pinion gear ring, it turned out that the pinion ring has been little tighter. Therefore, we are working on the new rings to address that. I will have an updated tomorrow.
Thanks,
--Alan
Bula Alan,
Hey, when the new jigmaster pinions come in, I'd like an additional full set, plus at least 2 - 9/0 gear sets.
AND.. with all these, are you still bringing out the 4:1 gear sets we can use in the 112h?
I'd like 2 of those too please ;)
Vinaka!
Quote from: Black Pearl on August 07, 2014, 03:01:23 AM
Hi guys,
I have received a lot of emails on the Jigmaster 5:1 gear set kit.
I have not received the shipment yet. I know that the 9/0 pinion gears are done for the past 2 weeks, and the Jigmaster's main, pinion gears are done last week. At the final stage, while testing the pinion gear ring, it turned out that the pinion ring has been little tighter. Therefore, we are working on the new rings to address that. I will have an updated tomorrow.
Thanks,
--Alan
Ok, the 9/0 pinion gears are on their way to here, and there are 2 sets of Jigmaster 500/501 with a new tighter pinion ring. I will send one set to Sal for testing approval. If it is approved, it will take 2 to 3 days to finished the product in Taiwan.
Thanks,
--Alan
Quote from: erikpowell on August 09, 2014, 05:34:18 AM
Bula Alan,
Hey, when the new jigmaster pinions come in, I'd like an additional full set, plus at least 2 - 9/0 gear sets.
AND.. with all these, are you still bringing out the 4:1 gear sets we can use in the 112h?
I'd like 2 of those too please ;)
Vinaka!
That is correct. I don't have the ETA on it at this moment. I have so many things going on.
Thanks,
--Alan
Can't wait to finalize my 9/0 with your pinions. I'm gonna have to get the dust out of my 9/0 cause it's been open for months on the bench. Keep us posted pal.
Thanks bro,
Dom
Well worth the wait bro. ;)...those are really nice ;).
The Jigmaster 5:1 gear set kit order is scheduled to arrive Florida on 08/18/2014. To place your order, please send email to sales@prochallenger.com or call 561-568-3980 by phone.
If any order is paid before 08/18/2014, it will ship out on the 08/18/2014.
Here is the specification and price.
1.) 316 stainless steel main gear.
2.) 420 staineless steel heat treated pinion gear.
3.) Helical precision cutting.
4.) True 5:1 ratio
5.) Smooth spin pinion.
6.) Modified sleeve spacer.
7.) $47.99 (original) and $49.99 (custom).
There will be 6% sales tax for any order shipping within Florida state.[/b][/color]
If anyone want to know the different between the standard and the custom main gear, please check out the following link by Bryan.
http://alantani.com/index.php?topic=6713.msg59428#msg59428 (http://alantani.com/index.php?topic=6713.msg59428#msg59428)
Hi Alan, I ordered the original set of custom gears. If I remember correctly the pinion gear was the weak link in these. Will the new pinion fit my original main gear? If not I'll be needing a new set. Right?
Bob
Quote from: BMITCH on August 14, 2014, 08:47:13 AM
Hi Alan, I ordered the original set of custom gears. If I remember correctly the pinion gear was the weak link in these. Will the new pinion fit my original main gear? If not I'll be needing a new set. Right?
Bob
Hi Bob,
I will replace the pinion gear, and I will include the sleeve spacing part as well.
Thanks,
Alan
Thanks Alan. Can't wait ;D
Hi Alan,
I also bought a set for the 112H. Am I going to get the new pinion gear?
Quote from: ML B on August 14, 2014, 07:06:48 PM
Hi Alan,
I also bought a set for the 112H. Am I going to get the new pinion gear?
Sorry, man. I sent you an email. This will not work in the 112H.
Alan, I don't believe that is a correct statement. This will be the strongest gear set available for a 112H. It is just that the max drag will be less that that of a Jigmaster due to the larger spool diameter. I intend to eventually replace the gears in all but 1 of my 112Hs with your gears and a stronger drag.
Ron
Quote from: noyb72 on August 14, 2014, 08:53:46 PM
Alan, I don't believe that is a correct statement. This will be the strongest gear set available for a 112H. It is just that the max drag will be less that that of a Jigmaster due to the larger spool diameter. I intend to eventually replace the gears in all but 1 of my 112Hs with your gears and a stronger drag.
Ron
You are correct, but there are few people will just try to use 20# of drag, therefore, I don't recommend to use it in the 112H. It will be hard for me to stand behind the product. I will try to do the best tho. I hope you know what I meant.
Now you can order this item or other parts I offer online. Please go to http://mkt.com/pro-challenger-llc (http://mkt.com/pro-challenger-llc) and place your order.
Hey Alan! The site you created, the page doesn't load right on my part
Marc..
Quote from: Marcq on August 15, 2014, 08:40:57 PM
Hey Alan! The site you created, the page doesn't load right on my part
Marc..
Try http://mkt.com/pro-challenger-llc (http://mkt.com/pro-challenger-llc)
Quote from: Black Pearl on August 15, 2014, 09:00:22 PM
Quote from: Marcq on August 15, 2014, 08:40:57 PM
Hey Alan! The site you created, the page doesn't load right on my part
Marc..
Try http://mkt.com/pro-challenger-llc (http://mkt.com/pro-challenger-llc)
Nope, when I choose the custom set, it goes into freeze mode and can't see the basket
Marc..
Quote from: Marcq on August 15, 2014, 09:15:12 PM
Quote from: Black Pearl on August 15, 2014, 09:00:22 PM
Quote from: Marcq on August 15, 2014, 08:40:57 PM
Hey Alan! The site you created, the page doesn't load right on my part
Marc..
Try http://mkt.com/pro-challenger-llc (http://mkt.com/pro-challenger-llc)
Nope, when I choose the custom set, it goes into freeze mode and can't see the basket
Marc..
It works on my PC and on my phone. Ok. I will send you an invoice via PayPal.
--Alan
Quote from: Black Pearl on August 15, 2014, 09:21:13 PM
Quote from: Marcq on August 15, 2014, 09:15:12 PM
Quote from: Black Pearl on August 15, 2014, 09:00:22 PM
Quote from: Marcq on August 15, 2014, 08:40:57 PM
Hey Alan! The site you created, the page doesn't load right on my part
Marc..
Try http://mkt.com/pro-challenger-llc (http://mkt.com/pro-challenger-llc)
Nope, when I choose the custom set, it goes into freeze mode and can't see the basket
Marc..
It works on my PC and on my phone. Ok. I will send you an invoice via PayPal.
--Alan
Got it Alan, is shipping included in the price?
Quote from: Marcq on August 15, 2014, 09:33:46 PM
Quote from: Black Pearl on August 15, 2014, 09:21:13 PM
Quote from: Marcq on August 15, 2014, 09:15:12 PM
Quote from: Black Pearl on August 15, 2014, 09:00:22 PM
Quote from: Marcq on August 15, 2014, 08:40:57 PM
Hey Alan! The site you created, the page doesn't load right on my part
Marc..
Try http://mkt.com/pro-challenger-llc (http://mkt.com/pro-challenger-llc)
Nope, when I choose the custom set, it goes into freeze mode and can't see the basket
Marc..
It works on my PC and on my phone. Ok. I will send you an invoice via PayPal.
--Alan
Got it Alan, is shipping included in the price?
All shipping is free within the USA.
Cool 8)
Thanks again Alan
Marc..
All guys,
I just got back home. I will start send out those replacement pinion gear with spacing sleeve parts. No main gear will be replaced.
Sorry for the delay.
Thanks,
--Alan
(http://i1280.photobucket.com/albums/a494/prochallenger/DSC07107_zpsc6a55b8f.jpg?t=1408592709)
(http://i1280.photobucket.com/albums/a494/prochallenger/DSC07108_zpsfdf85514.jpg)
I bought a jigmaster 500 and I'm going to put stock steel gears in my 112HN. When you have the replacement pinions ready for shipping, put me on the list please. No rush, I'm busy with other things.
I will need one please
Quote from: floating doc on August 22, 2014, 01:02:43 PM
I bought a jigmaster 500 and I'm going to put stock steel gears in my 112HN. When you have the replacement pinions ready for shipping, put me on the list please. No rush, I'm busy with other things.
Doc, BP's gears and pinion are helical. The BP pinion will not work with the stock Penn gears. You would have to have BP's main and pinion.
You probably already know this. ;D Bob
Quote from: broschro on August 22, 2014, 03:51:16 PM
I will need one please
Quote from: floating doc on August 22, 2014, 01:02:43 PM
I bought a jigmaster 500 and I'm going to put stock steel gears in my 112HN. When you have the replacement pinions ready for shipping, put me on the list please. No rush, I'm busy with other things.
Guys,
Please send me your email address and your mailing address, please.
Thanks,
--Alan
Quote from: Cone on August 22, 2014, 04:26:53 PM
Quote from: floating doc on August 22, 2014, 01:02:43 PM
I bought a jigmaster 500 and I'm going to put stock steel gears in my 112HN. When you have the replacement pinions ready for shipping, put me on the list please. No rush, I'm busy with other things.
Doc, BP's gears and pinion are helical. The BP pinion will not work with the stock Penn gears. You would have to have BP's main and pinion.
You probably already know this. ;D Bob
Yes, but it's really nice of you to point that out.
I bought the original set for my 112HN. Since the BP gears won't work in those reels, I'm going to build a jigmaster. I'm not giving up!
Come and get it now.
This gear set kit is also available via Smooooth Drag and Brian's Fishing Supply in Hawaii.
still no love for the 112h?
I am in for one set
Speedwagon2
A new version 5:1 gear set will be tested by Sal to confirm if it will work for Jigmaster 500/501 and 112H.
Here is a picture.
(http://i1280.photobucket.com/albums/a494/prochallenger/503a4f91-3de5-4920-849b-937fda71e767_zps3eya26lq.jpg)
Alan....is the ring on the pinon a press fit?
Quote from: swill88 on January 31, 2016, 03:14:20 AM
Alan....is the ring on the pinon a press fit?
Yes it is.
I know you have lot of pokers in the fire, but when is the 500 gear going to get the new drag?
Ron
Quote from: noyb72 on February 14, 2016, 11:23:27 PM
I know you have lot of pokers in the fire, but when is the 500 gear going to get the new drag?
Ron
Is 4:1 or 5:1 you talking about?
I've seen the 4:1, but the 5:1 would be nice also.
Ron