Text only | Text with Images

Reel Repair by Alan Tani

Conventional and Bait Casting Reel Rebuild Tutorials and Questions => Avet Tutorials and Questions => Topic started by: trentless on March 27, 2011, 01:14:02 PM

Title: Avet sx 5.0.1, help hard to use
Post by: trentless on March 27, 2011, 01:14:02 PM
I just finished tinkering with, oops I mean servicing my buddy's SX 5.1 (older style) and it is very difficult to turn the handle now.  It has good drag and freespool so I assume the lever drag got moved durring build back.  The braid isn't slipping and the spool is not overloaded.  How the heck do I fix this and also prevent it from happening again???  Do you back of the drag, freespool to make it fool proof when putting back together?

Thanks
Title: Re: Avet sx 5.0.1, help hard to use
Post by: Nessie Hunter on March 27, 2011, 03:13:41 PM
Assuming here!!!   
You probably dont have the gears & pins seated into Drag/spool stack..
Have to remove Rght side again and make sure all is seated as you put it back together, slowly & carefully.
I turn the handle as it comes together and hope for the best.   
Sometimes takes a couple of tries "for me" ....

Alan or others may have an easier way to do it???

The drag adjustment isnt the issue, it the fitting back together gears & gear pins back into spool exactly right. 
Title: Re: Avet sx 5.0.1, help hard to use
Post by: trentless on March 27, 2011, 05:01:29 PM
Thanks Nessie Hunter,
I figured it was something pretty simple, just a pain to find out after its all put back together!  Need to figure out how to make servicing these idiotproof.  Might have time to redo here today.
Title: Re: Avet sx 5.0.1, help hard to use
Post by: alantani on March 27, 2011, 08:21:31 PM
any possibility that the right main side plate bearing is bad?  also, could you have forgotten to install the sleeve between the two drive shaft bearings? 
Title: Re: Avet sx 5.0.1, help hard to use
Post by: trentless on March 28, 2011, 12:21:31 AM
Hey Alan,
No extra parts, so the sleeve isn't the issue. By right side plate bearing do you mean drive shaft bearing (key24 2 req)?  What's the best way to deal with the lever drag/preset knob when servicing these reels?  Do you set them to free to avoid miss-alignment?  What should the max drag be on this reel?

Took everything apart, re-assembled with considerable improvement except for random grinding after pulling drag while testing settings.  Handle still seems hard to turn when full drag is applied, and as stated; random momentary grinding sound after spool/drag pulled.  It goes away after 2-3 cranks?  I think it might need a few bearings.  The spool & brake bearing looked rough and this might explain the symptoms.  Again its not my reel, like you I have the illness/obsession of tinkering with reels only I'm @ stage 1 !  ;D 
I will probably call Avet in the am for guidance and order new bearings.
Any thoughts?

Thanks
Title: Re: Avet sx 5.0.1, help hard to use
Post by: alantani on March 28, 2011, 01:12:33 AM
it's key #23 (pinion bearing) that always fails.  http://www.avetreels.net/uploads/SX_5.3.pdf  the lever should be in the free position when screwing down the preset knob.  the max drag is 8-9 pounds. 
Title: Re: Avet sx 5.0.1, help hard to use
Post by: trentless on March 28, 2011, 12:51:11 PM
Ok, same bearing, different key #, this is a SX5.1 not 5.3.  Will try 1 more time then call Avet if drag-grind noise continues.  How do you determine if a bearing is bad, or do you just assume age & neglect warrants it?
Title: Re: Avet sx 5.0.1, help hard to use
Post by: alantani on April 06, 2011, 01:08:40 AM
hold the outer race in your left hand, push on the inside race with your right index finger and twist.  if you feel any roughness at all, the bearing should be tossed.
Text only | Text with Images