hello all im a new member in this site, any of you guys wonder or knw what one is better in reels is it the sealed ball bearings or is it the open ones and how long before the sealed ones need changing and how to open the seal without damaging the bearing this is really getting to me as my penn special senators have sealed ball bearings while my tlds have the open ones that are easy to clean and service any help or info on this would be a great help thanks and cheers guys ;)
I do not know how to do the fancy links, but you can find it under "general procedures" topic bearings. it will give you everything.
Hi Trishul,
There's a vast amount of information on Alan's site about bearing types, maintenance etc.
To reinforce Rodent's suggestion, perhaps try a search on 'bearings' and scan through the results (you may need to set aside an evening or two, though!).
On balance, open bearings are generally better if you maintain your reels regularly.
An array of variables such as bearing quality and composition, bearing purpose and size, lubrication type and fishing style (to name but a few) all have an influence...
All the best, Justin
Try these for starters.
http://alantani.com/index.php?topic=2328.0
http://alantani.com/index.php?topic=1970.0
thanks alot guys very helpfull indeed tight lines to all :)
Do you have any other questions after reading the discussion, please post and we will do our best to answer you.
hello for now not really i am just absorbing all the info on the site but im sure i will in future cheers and thanks alot again this site and you all are a good wealth of info ohh n by the way i tried opening some bearing its a fidly job esp on small bearings but its doable :)
it's an awful lot to absorb, i know. the search functions with this software are not the best. when you are just starting, there is a very high probability that your question has been asked and answered before. in general, i think it's best if you do this. first, try a search and check around a little. if you don't find your answer after a minute or two, go ahead and post your question. i don't want you spinning your wheels all day. and welcome!!!!
And the 'Search' only searches the board you're in, so for maximum results search from the home page. If you want to filter a bit, go to a specific board (like "General Procedures") and search there.
ok thanks will do :)
I just destroyed my first bearing trying to pry off the pressed in seal. This cover was on a small bearing, and it was a bear. I tried a fish hook, a dental pick, and finally destroyed it with the tip of a thin knife. I didn't have a scapel, and I'm kind of glad, because of the pressure I was using, I could lose a finger! Any tips would be appreciated! David
It's relatively less important to get the shields off small bearings and certainly not worth doing yourself an injury in the process.
I'll sometimes use WD-40 or carb cleaner (through the straw) straight against the shield of particularly small bearings, then force in grease (or ReelX etc).
Alan's bearing packer will push grease straight through, regardless of the shield, so you may want to consider one of those.
Here's the link: http://alantani.com/index.php?topic=870.0 (http://alantani.com/index.php?topic=870.0)
There's also some good info here: http://alantani.com/index.php?topic=13 (http://alantani.com/index.php?topic=13).
Good luck, Justin
hi david you may want to try a sewing needle a tiny one thats what i did and it worked fine, by the way just curious what reel was the bearing from
thanks
trishul
Hello Trishul. The bearing I broke was the small spool bearing from a TLD 20. It was pressed in, and didn't have the collar key to remove. Those are easy, but this one was a bear. I damaged the race pushing the tip in too far and lifting. For really tiny bearings, I found that a 25 gauge needle from a syringe is sharp enought to get under that fine collar and lift them out. I have to older TLD 20's and both are stamped from Japan on the reel seat. The older of the two had spool bearings without the collars.
hi dave i got the same reel but i got mine just two years ago and the other in 2006 they are all written product of malaysia but soo far have been working great and servicing and repacking the bearings is not too bad but i use the needles to remove the shield, by the way all cheap shimano reels i think under 300usd are made now in malaysia i got a stella its says japan, soo are cheaper penns but i got a size 16 thats from USA, got all my reels from tackledirect
sorry dave the penn was a senator 116l that was made in usa the other senator i got a 113H2 was made in china all i got in 2010 and all from tackledirect was not too happy with the made in china sign but i can just scratch it out ;D and hey as far as the reel work fine its ok with me but i dont fully trust some china items its just my view, i rather trust malaysia
Quote from: trishul on July 29, 2011, 12:18:34 PM
hi david you may want to try a sewing needle a tiny one thats what i did and it worked fine, by the way just curious what reel was the bearing from
thanks, trishul
now THAT is a fabulous idea!
Quote from: trishul on July 31, 2011, 09:44:27 AM
sorry dave the penn was a senator 116l that was made in usa the other senator i got a 113H2 was made in china all i got in 2010 and all from tackledirect was not too happy with the made in china sign but i can just scratch it out ;D and hey as far as the reel work fine its ok with me but i dont fully trust some china items its just my view, i rather trust malaysia
in all fairness, the new chinese jigmasters are a better quality reel than the old american jigmasters....... :-\
i agree alan china have good items and bad items also just time will tell once the reels have been put through alot of extensive use and testing but i just belive its like in the mind as im sure penn will not allow china to make low quality as there must be certian quality control and standards that are meet