I don't have this part anymore. I have to save one for one of the member here.
If anyone wants this parts, SmoothDarg and Scott's will be your best source.
Brian's Fishing Supply
Scott's Bait & Tackle in NJ.
Description:
- stainless steel bridge plate
- stainless steel right and left dogs
- stainless steel dog secure "C" clip for each dog
- stainless steel machined gear sleeve post
- Stainless steel dog spring for each dog
- Fits original Penn and Accurate side plates with no alternation (just remove the existing dog)
The following picture shows that how the dog springs should install with the dogs.
http://i1280.photobucket.com/albums/a494/prochallenger/8726c106-f8d1-4bb2-a87c-0e77250ff984_zpsupr5dtat.jpg (http://i1280.photobucket.com/albums/a494/prochallenger/8726c106-f8d1-4bb2-a87c-0e77250ff984_zpsupr5dtat.jpg)
Please note that the gear sleeve is sold separately.
Thanks,
--Alan
I'll take one set. RUDY
Alan, 2 sets for me please.
Thanks!
Steve
As always, the drag numbers I've mention to Alan are stress test only. I'm impressed with the full package on this one, Bridge-Sleeve and Gears.This reel could take lots of abuse.
Sal
I'll take a set.
Sid
I'm in for one set!
One for me to put in my Pro Gear 545.
I would like 2 please!
................Lou
I,ll take one please
Put me down for two please
4 sets please
Put me down for 1 set please.
Ron
I have one of the first R&D run of these and love it.
Order qty: 2 sets please!
Ill take 2 sets
Ill take two sets also.
Mike
1 please
I'm in for one set..
Chad
Four please
sounds great Alan.....
.........count me in for 4 please.
One for me too, please!
Put me in for two. Thanks Alan.
Charlie
1 set for me please. thanks! Steve
my email: slee1061@sbcglobal.net
Im in for 7 --- thanks
1 set Alan,
Thanks
Going to need 3
1 set Please.
1 set please , thanks mitch27
Alan, Im in for 2 sets/.
Thanx,
Leo
53 sets have been called for. Thank you guys.
At some points, I will lock this thread because some sets will have to save for SmoothDrag and Scott's.
Alan, Will you give us a last call before locking down? I could use one (1) additional but only reserved two (2) just to make sure there's enough to go around. If there will be additional runs later on down the road, I could wait until then.
Thank you for making these available.
-Mike
One set for me please.
Quote from: PacRat on February 07, 2016, 05:33:48 PM
Alan, Will you give us a last call before locking down? I could use one (1) additional but only reserved two (2) just to make sure there's enough to go around. If there will be additional runs later on down the road, I could wait until then.
Thank you for making these available.
-Mike
Hi Mike,
I will give it a last call before locking down of this thread. I believe that 50 sets will be called for by SmoothDarg and Scott's.
About additional production runs, That will be depended on the market demand. I hope you can understand that.
Thanks,
--Alan
Alan,
4 for me please.
Thanks,
Dom
PS- these will work with your 1st run gears and a standard ss sleeve, correct?
Quote from: broadway on February 07, 2016, 08:03:54 PM
Alan,
4 for me please.
Thanks,
Dom
PS- these will work with your 1st run gears and a standard ss sleeve, correct?
That is correct.
Perfect! Can't wait to fill my 4 wire line reels with these.
Thanks
Dom
1set for me please Alan
Bob
2 sets for me please
Peter
I don't remember if I ordered but I will take 2 sets.
Eugene
1 set please
Alan,
2 sets for me. Can't wait
Speedwagon2
Definitely one set for me, please! :)
~A~
add me for 1 set please.. addy in USA so USPS is perfect for me
Alan,
2 sets for me please!
Thanks, Sergey
Alan,
Four sets for me please. Thanx in advance.
Eric
1 for me
I would like to order one more. That would be a total of 2. Thanks. Ken
To Ken:
10-4. I removed your previous posting.
Thanks,
--Alan
Put me down for 1 set please. Aloha
need 2 please ;D
ETA: any idea is these are drop in for the Pro Gear 545?
Alan, I would like to reserve one set as well.
Thanks, Ed
Quote from: badfish71 on February 10, 2016, 12:31:40 AM
need 2 please ;D
ETA: any idea is these are drop in for the Pro Gear 545?
Hi there,
We don't know if it will fit the PG 545 or any Newell. Hopefully, we will find out down in the road.
Thanks,
--Alan
Hi Alan, I previously ordered 4 DD bridges and would like to add (2) more for a total of (6).
These will be on my trolling rods (albacore), and I have no doubt they'll be able to pull a planer board going 6 knots, which is impossible with stock 113H.
Has anyone tested whether the DD bridge will drop into a accurate jigmaster magnum ?
Ted
Quote from: Max Doubt on February 10, 2016, 07:32:06 PM
Hi Alan, I previously ordered 4 DD bridges and would like to add (2) more for a total of (6).
These will be on my trolling rods (albacore), and I have no doubt they'll be able to pull a planer board going 6 knots, which is impossible with stock 113H.
Has anyone tested whether the DD bridge will drop into a accurate jigmaster magnum ?
Ted
I'm planning on putting these in the jigmaster magnum, if the stock bridge fits, these will fit.
Quote from: Max Doubt on February 10, 2016, 07:32:06 PM
Hi Alan, I previously ordered 4 DD bridges and would like to add (2) more for a total of (6).
These will be on my trolling rods (albacore), and I have no doubt they'll be able to pull a planer board going 6 knots, which is impossible with stock 113H.
Has anyone tested whether the DD bridge will drop into a accurate jigmaster magnum ?
Ted
I am pretty sure it will fit, but I will have Sal checking into it.
Quote from: Max Doubt on February 10, 2016, 07:32:06 PM
These will be on my trolling rods (albacore), and I have no doubt they'll be able to pull a planer board going 6 knots, which is impossible with stock 113H.
Ted
You might also need the 2nd gen gear set to go with it.
Quote from: Black Pearl on February 10, 2016, 08:41:49 PM
Quote from: Max Doubt on February 10, 2016, 07:32:06 PM
Hi Alan, I previously ordered 4 DD bridges and would like to add (2) more for a total of (6).
These will be on my trolling rods (albacore), and I have no doubt they'll be able to pull a planer board going 6 knots, which is impossible with stock 113H.
Has anyone tested whether the DD bridge will drop into a accurate jigmaster magnum ?
Ted
I am pretty sure it will fit, but I will have Sal checking into it.
Can't help you there bud, I do not own a magnum and would not want to use anyone else, I've ruined plenty of my own reels with these tests. :-\.
If the stock bridge will work I don't see why this one wouldn't, but you never know.
Sal
Alan,
I plan on putting one of mine in a Magnum. I'll let you guys know how it fits.
I originally ordered two (2), maybe three (3). I would like to confirm three (3) units.
Thanks
-Mike
I'll buy the one from you and any extras from Bryan. I really do what I can to keep him in business.
Ron
One set for me please Alan
Mike
Hi Alan -
Please put me down for 1 set.
Matt
Quote from: noyb72 on February 11, 2016, 06:21:39 AM
I'll buy the one from you and any extras from Bryan. I really do what I can to keep him in business.
Ron
I respect that. That was why I contacted Brian to carry it.
1 for me please!
i need (3) three.
thanks,
mark
I'd like 4.
Thanks again,
Anthony
Alan
I would like one set. Thanks,
John
Today is the last day that I am taking a per-order of this item.
Anyone still can place a pre-order at following vendors.
Scott's Bait and tackle: (609) 296-1300 Ask for Mo
SmoothDrag: (888) 206-4656
Brian's Fishing Supply in Honolulu: (808) 596-8344
Thank you guys!!!!
Hi Alan, did you get my order? If not, I'll get them from one of the vendors. Thank you,
Bryan
Quote from: Bryan Young on February 28, 2016, 06:19:01 AM
Hi Alan, did you get my order? If not, I'll get them from one of the vendors. Thank you,
Bryan
Hi Byran,
Sorry, they are all spoken for. You can contact SmoothDrag or Scott's Bait & Tackle to reserve your order.
Thanks,
Alan
There is a little setback on this part. The problem Is on both dogs. The factory made a mistake on cutting them too tight. Therefore, we have to order some more SS raw material to make those parts again.
This is just a headache, and I know there are a lot of people waiting for this product to release.
I will try to push them little faster on production.
Sorry for the delay.
Thanks,
Alan C
Here is the latest on this part. This thread is unlocked for updating only.
This part will be available for shipping by mid of May. It will come to the US with those "Easy Access" gear set order.
For those member who placed his order within this thread., please post your email address or send me a PM with your email address for an invoice. I will send out the invoice in 2 weeks. If the invoice is not paid in 3 days, the order will be cancelled.
Thanks,
--Alan C.
Hi Alan, if order is cancelled, can I be placed on the waiting list? I have a few individuals that asked me to upgrade their reels with your bridge plate. Thanks, Bryan
Quote from: Bryan Young on April 22, 2016, 02:58:24 PM
Hi Alan, if order is cancelled, can I be placed on the waiting list? I have a few individuals that asked me to upgrade their reels with your bridge plate. Thanks, Bryan
Sure. Have you checked with SmoothDrag? Dawn is taking order as well.
Quote from: Bryan Young on April 22, 2016, 02:58:24 PM
Hi Alan, if order is cancelled, can I be placed on the waiting list? I have a few individuals that asked me to upgrade their reels with your bridge plate. Thanks, Bryan
I feel that there will be few sets available because some members changed their mind.
Here is the latest on this part.
This part will be available for shipping by mid of May. It will come to the US with those "Easy Access" gear set order.
For those member who placed his order within this thread., please post your email address or send me a PM with your email address for an invoice. I will send out the invoice in 2 weeks. If the invoice is not paid in 3 days, the order will be cancelled.
Thanks,
--Alan C.
All parts are in the factory now. It should be starting assemble very soon. Priveting the sleeve post and dog posts manually.
It should be done and ship to the US very soon.
Just got an updated from the resource. This part will ship to me by next Friday. Invoice will be sent to all members who reserved an order for this part.
Please note that if the invoice is not paid in 3 days, the order will be cancelled.
Thanks,
--Alan
Hi Alan,
If anyone cancels, please let me know.
Bryan
Quote from: Bryan Young on April 29, 2016, 09:00:57 PM
Hi Alan,
If anyone cancels, please let me know.
Bryan
How many are you looking for? I know there are few people would not reply my PM, so, I will consider their orders are cancelled.
I need 6 if possible. A few more if available.
Note that ill be out of town for 2 weeks beginning next Friday.
Unlocking this thread since I recorded all members who placed their order.
Alan,
Is it possible to still order 2 double dog bridges from you?
Thanks,
Max
Aloha Alan,
I should be on the list for 1 set, if possible can you add 1 more for a total of 2 bridges?
Thanks!
Quote from: napilimaui on April 30, 2016, 08:28:07 PM
Alan,
Is it possible to still order 2 double dog bridges from you?
Thanks,
Max
Hi Max,
At this moment, I don't know if there is any cancel order yet. I should be able to let you know if there is any left.
Thanks,
--Alan
If there's another batch I'm in for one Alan
Marc..
Quote from: Marcq on May 01, 2016, 05:50:51 AM
If there's another batch I'm in for one Alan
Marc..
Hi Marc,
No, it will be awhile before there will be another batch to be made. You should order it from Smooth Drag.
All members who pre-ordered this part should receive an invoice today.
Please note that if the invoice is not paid by end of 05/04/2016, I will cancel the order. In addition, the shipping date will be around 05/13/2016.
Please let me know if you have any questions.
Thank goodness that this part is ready. It has been a long haul on this part.
Thanks,
--Alan C.
Payment has been completed. Thank you for making this available, it will be used in Accurate plates.
Paid.
Mike
:D PAID! :D Rudy
Paid in full. Thanks for making this awesome part available to us, no more flying dog springs!
Aloha,
Kyle
Paid! Thanks for making these available
X3! :D
Paid! Thanks for making such great toys for us!
Sid
Quote from: Yogi_fish808 on May 01, 2016, 07:12:43 PM
Paid in full. Thanks for making this awesome part available to us, no more flying dog springs!
Aloha,
Kyle
Your gonna miss the flying dog springs!
paid in full, can't wait to get it!
paid in full, thanks.
Quote from: Black Pearl on May 01, 2016, 04:26:50 PM
All members who pre-ordered this part should receive an invoice today.
I haven't received an invoice yet Alan, did you receive my PM confirming my order?
Thanks
Mike
Done!
Paid in full. And I too would thank you for your effort in this project..much appreciated. Eric
paid!! cant wait!
Paid and can't wait to get another quality Black Pearl upgrade.
Quote from: Black Pearl on May 01, 2016, 12:30:55 PM
Quote from: Marcq on May 01, 2016, 05:50:51 AM
If there's another batch I'm in for one Alan
Marc..
Hi Marc,
No, it will be awhile before there will be another batch to be made. You should order it from Smooth Drag.
No problemo Alan, I'll check Smooth Drag
Thanks, Marc..
pretty excited to get this! my new set of plates are patiently waiting on the workbench, then all will go back on my favorite yts along with some other nice upgrades. thanks Alan 8)
Paid!
Here is the latest on any cancelled and pending orders as of 05/02/2016.
Member Qty Status
====================================
mberggre 1 order cancelled
Cbar45 1 invoice sent and Pending
broschro 1 invoice sent and Pending
garking84 1 invoice sent and Pending
Alasken 2 invoice sent and Pending
steelfish 1 order cancelled
mhc 1 oversea member invoice not sent yet (Reserved)
p-deverett 2 oversea member invoice not sent yet (Reserved)
Billyhill 1 oversea member invoice not sent yet (Reserved)
noyb72 1 Pending
army_of_one 2 Cancelled
garyal 1 Cancelled
theluckpusher 7 Cancelled
surfcaster 1 Cancelled
crackerman 1 invoice sent and Pending
napilimaui 2 waiting list
Marcq 1 waiting list
The latest updated.
The shipment of this part, from Taiwan, is pushing back for 1 week. We found that the dog springs was not strong enough, so we asked our spring factory to make a stronger spring batch in a week. Due to this problem, our shipping date will be around 05/20/2016. If any paid member does not want to wait and would like to have a full refund, please let me know, and I will refund the payment at once.
Sorry for the delay, but it is a right thing to do.
Thanks,
--Alan
Alan, not sure if I should be on the list, but I paid and am waiting too ....
Sid
Quote from: sdlehr on May 10, 2016, 02:05:50 PM
Alan, not sure if I should be on the list, but I paid and am waiting too ....
Sid
If you paid the PayPal invoice I sent you, you are on the list to have the part to be shipped to you when the shipment get to the US.
Thanks,
Alan
Quote from: Black Pearl on May 03, 2016, 02:21:13 AM
Here is the latest on any cancelled and pending orders as of 05/02/2016.
Member Qty Status
====================================
mberggre 1 order cancelled
Cbar45 1 invoice sent and Pending
broschro 1 invoice sent and Pending
garking84 1 invoice sent and Pending
Alasken 2 invoice sent and Pending
steelfish 1 order cancelled
mhc 1 oversea member invoice not sent yet (Reserved)
p-deverett 2 oversea member invoice not sent yet (Reserved)
Billyhill 1 oversea member invoice not sent yet (Reserved)
noyb72 1 Pending
army_of_one 2 Cancelled
garyal 1 Cancelled
theluckpusher 7 Cancelled
surfcaster 1 Cancelled
crackerman 1 invoice sent and Pending
napilimaui 2 waiting list
Marcq 1 waiting list
Hi Alan -
I either missed the paypal invoice or I fat fingered my email address. I've sent you a few PMs and an email. I would love to buy one of these from you if my bridge hasn't been sold already.
Matt
Quote from: mberggre on May 10, 2016, 04:49:07 PM
Quote from: Black Pearl on May 03, 2016, 02:21:13 AM
Here is the latest on any cancelled and pending orders as of 05/02/2016.
Member Qty Status
====================================
mberggre 1 order cancelled
Cbar45 1 invoice sent and Pending
broschro 1 invoice sent and Pending
garking84 1 invoice sent and Pending
Alasken 2 invoice sent and Pending
steelfish 1 order cancelled
mhc 1 oversea member invoice not sent yet (Reserved)
p-deverett 2 oversea member invoice not sent yet (Reserved)
Billyhill 1 oversea member invoice not sent yet (Reserved)
noyb72 1 Pending
army_of_one 2 Cancelled
garyal 1 Cancelled
theluckpusher 7 Cancelled
surfcaster 1 Cancelled
crackerman 1 invoice sent and Pending
napilimaui 2 waiting list
Marcq 1 waiting list
Hi Alan -
I either missed the paypal invoice or I fat fingered my email address. I've sent you a few PMs and an email. I would love to buy one of these from you if my bridge hasn't been sold already.
Matt
Hi,
I resent your invoice three times. Please check your gmail account.
Thanks,
Alan
Quote from: Black Pearl on May 03, 2016, 02:21:13 AM
Hi,
I resent your invoice three times. Please check your gmail account.
Thanks,
Alan
Thanks, Alan. I just tracked it down and paid you! I apologize for the misunderstanding.
Quote from: mberggre on May 10, 2016, 09:38:47 PM
Quote from: Black Pearl on May 03, 2016, 02:21:13 AM
Hi,
I resent your invoice three times. Please check your gmail account.
Thanks,
Alan
Thanks, Alan. I just tracked it down and paid you! I apologize for the misunderstanding.
No problem.
Thanks,
--Alan
Just got back from sea. I'll settle up soonest.
Thanks
Ron
Alan, if there's any stragglers or leftovers, let me know....or at least put me on the list ;D
Vinaka
Erik
Quote from: erikpowell on May 11, 2016, 08:44:39 AM
Alan, if there's any stragglers or leftovers, let me know....or at least put me on the list ;D
Vinaka
Erik
Hi Erik,
I can't promise there will be any leftovers, but how many are you looking for?
Thanks,
Alan
I didn't see my name on the list, but you and I had spoken so I figure I'm covered. You got me covered, correct Alan?
Thanks
Dom
Quote from: broadway on May 11, 2016, 07:36:51 PM
I didn't see my name on the list, but you and I had spoken so I figure I'm covered. You got me covered, correct Alan?
Thanks
Dom
Yep!
By the way, if any member who purchased this SS double dog bridge wants to add a SS eccentric jack (PC11-113) in his order, he can just send a PayPal gift of $7.99 each to my PayPal account (prochallenger@yahoo.com). This part will ship with the bridge order together because it saves you guy on $2.45 + PayPal fee.
(http://i1280.photobucket.com/albums/a494/prochallenger/E1060DB4-349E-420C-966B-1A0283C6AB92_zps3usndf9u.jpg)
All these parts are shipping out from Taiwan to the USA today. I should have it by coming this Friday, and all paid orders will ship out this Saturday to members.
Anyone who also paid for the Jack part, that order will also ship out with your paid bridge order together.
Thank you all your patient!!!!!!
Thanks,
--Alan C
They are on route to be in the US.
Are we ready?
(http://i1280.photobucket.com/albums/a494/prochallenger/FA1AD5B6-2BD7-4FD1-9635-8647E56A7794.png_zps8ywn1b3s.jpeg)
Exciting stuff!
Sounds like Santa Claus is onroute.
BTW has anyone tested these in JVariance, Accurate, and the other aftermarket side plates yet?
I didn't order any items directly from you. I will pick mine up from Brian's Fishing here in Honolulu once I know it will work in my JVARIANCE plate.
Thanks again for making these available!
John
Quote from: Black Pearl on May 11, 2016, 09:59:13 PM
By the way, if any member who purchased this SS double dog bridge wants to add a SS eccentric jack (PC11-113) in his order, he can just send a PayPal gift of $7.99 each to my PayPal account (prochallenger@yahoo.com). This part will ship with the bridge order together because it saves you guy on $2.45 + PayPal fee.
(http://i1280.photobucket.com/albums/a494/prochallenger/E1060DB4-349E-420C-966B-1A0283C6AB92_zps3usndf9u.jpg)
Sent you paypal for three
I can hardly wait !
Quote from: Tightlines666 on May 16, 2016, 07:11:52 PM
Exciting stuff!
Sounds like Santa Claus is onroute.
BTW has anyone tested these in JVariance, Accurate, and the other aftermarket side plates yet?
I didn't order any items directly from you. I will pick mine up from Brian's Fishing here in Honolulu once I know it will work in my JVARIANCE plate.
Thanks again for making these available!
John
Hi John,
We tested it in Penn's side plates ( old and new) and Accurate.
Thanks,
Alan
Quote from: Black Pearl on May 16, 2016, 05:45:21 PM
They are on route to be in the US.
Are we ready?
(http://i1280.photobucket.com/albums/a494/prochallenger/FA1AD5B6-2BD7-4FD1-9635-8647E56A7794.png_zps8ywn1b3s.jpeg)
Wow Alan, very impressive. That's a lot of man hours in that box of custom parts.....and a lot of future "Tanks" yet to be built, thanks to you 8) 8)
Ted
Quote from: Black Pearl on May 16, 2016, 08:17:20 PM
Quote from: Tightlines666 on May 16, 2016, 07:11:52 PM
Exciting stuff!
Sounds like Santa Claus is onroute.
BTW has anyone tested these in JVariance, Accurate, and the other aftermarket side plates yet?
I didn't order any items directly from you. I will pick mine up from Brian's Fishing here in Honolulu once I know it will work in my JVARIANCE plate.
Thanks again for making these available!
John
Hi John,
We tested it in Penn's side plates ( old and new) and Accurate.
Thanks,
Alan
JVariance side plates are basically an exact copy of the Accurate plates as far as I can tell
Quote from: day0ne on May 16, 2016, 11:51:51 PM
Quote from: Black Pearl on May 16, 2016, 08:17:20 PM
Quote from: Tightlines666 on May 16, 2016, 07:11:52 PM
Exciting stuff!
Sounds like Santa Claus is onroute.
BTW has anyone tested these in JVariance, Accurate, and the other aftermarket side plates yet?
I didn't order any items directly from you. I will pick mine up from Brian's Fishing here in Honolulu once I know it will work in my JVARIANCE plate.
Thanks again for making these available!
John
Hi John,
We tested it in Penn's side plates ( old and new) and Accurate.
Thanks,
Alan
JVariance side plates are basically an exact copy of the Accurate plates as far as I can tell
That's what I suspect, but I have never had them sitting side-by-side.. I will pick one up from Brian, when they arrive, and try it out. My bet is that it is going to work just fine.
Why wouldn't they?
Quote from: Alto Mare on May 17, 2016, 01:22:26 AM
Why wouldn't they?
Usually when an aftermarket parts doesn'the quite fit right.. I would chalk it up to 'clearance ossues'. I am aware it's nearly impossible to test these parts in every variant of the reel model they were designed for, but inferenceshe can certainly be made. Like it works in the Accurate plate, so it will work in the JVariance or LeePro, or the old school Penn plates with that were madeven for only right or left hand reels, may not have enough clearance. Just musing, but I just thought I would ask if there were any known incompatibility issues with these bridges as of yet.
I am sure they will work great, and will likely be compatible with most, if not all plates.
As for tolerance you are absolutely correct John.
Here is the JVariance plate, this is just the bridge test and nothing else:
(http://i1101.photobucket.com/albums/g431/pescatore1/20160516_214707.jpg) (http://s1101.photobucket.com/user/pescatore1/media/20160516_214707.jpg.html)
You probably can't see it, but the sleeve doesn't sit completely centered to the hole. Still, I don't believe it would be an issue.
(http://i1101.photobucket.com/albums/g431/pescatore1/20160516_214651.jpg) (http://s1101.photobucket.com/user/pescatore1/media/20160516_214651.jpg.html)
Here is Tom's plate:
(http://i1101.photobucket.com/albums/g431/pescatore1/20160516_220332.jpg) (http://s1101.photobucket.com/user/pescatore1/media/20160516_220332.jpg.html)
(http://i1101.photobucket.com/albums/g431/pescatore1/20160516_220343.jpg) (http://s1101.photobucket.com/user/pescatore1/media/20160516_220343.jpg.html)
A perfect fit, just as the Accurate. This tells me Tom's are milled from Accurate, but I might be wrong.
With all of these custom parts, it's always a good practice to set all screws loose and tighten them gradually, plate and frame.
Sal
Great Job Sal... a picture (or 3) are worth 1000 words. Looks like these will work in out just fine, not that I ever really ad any doubts. I do agree with your assessment that they seem to center best in the Accurate headplates. Looks like the pinion should still clear fine, and have enough meat on the teeth to engage cleanly on all 3 plates tested, just gauging by eye there.
Thanks for sharing the pictures Sal.
payment sent for 1 ss eccentric. thanks, Steve
Payment sent for one SS eccentric jack to include when shipping my bridge.
Sid
payment sent for jack with bridge
paid for 2 eccentrics.
Payment sent for 2 SS eccenetric jacks to ship with double dog bridges
Dave Babcock AKA Speedwagon2
The shipment arrived Miami. I will have it in my possession tomorrow noon, and I will start assembling and shipping all paid order. I hope that all paid order will ship out by Saturday.
Thanks,
Alan
QuoteInsert Quote
The shipment arrived Miami. I will have it in my possession tomorrow noon, and I will start assembling and shipping all paid order. I hope that all paid order will ship out by Saturday.
Thank you Alan, I am looking forward to receiving this bridge.
Hi,
Some of you should receive an email from PayPal about your order was shipped. If you have not received any email, don't worry. It will come. I am doing as fast as I can.
Thanks,
--Alan
Quote from: Black Pearl on May 20, 2016, 09:17:17 PM
Hi,
Some of you should receive an email from PayPal about your order was shipped. If you have not received any email, don't worry. It will come. I am doing as fast as I can.
Thanks,
--Alan
No problemo Alan
Marc..
All orders are done.
Not until the fat lady sings
Mike
I received an email stating that it's been shipped!
Just checked and yes it shipped.
Thanks for keeping us in the loop on this!
Chad
Thanks Alan C and to Sal for the testing.
Hi all,
The following picture shows that how the dog springs should install with the dogs.
(http://i1280.photobucket.com/albums/a494/prochallenger/8726c106-f8d1-4bb2-a87c-0e77250ff984_zpsupr5dtat.jpg)
Please note that the gear sleeve is sold separately.
I got my tracking notice, too... many thanks, Alan! :)
~A~
got my notice... thanks!
those eclips are beautiful!
steve
Where's the mailman where's the mailman where the mailman
Guess what the mailman just delivered! Christmas in May!! Thank you Alan!
Quote from: PacRat on May 23, 2016, 07:50:52 PM
Guess what the mailman just delivered! Christmas in May!! Thank you Alan!
That was fast for the First Class Package Mail Service.
Mine is out for delivery but the mailman never delivers the mail till after 6:00 PM.
West coast delivery times..................... ::)
Quote from: RowdyW on May 23, 2016, 08:45:15 PM
Mine is out for delivery but the mailman never delivers the mail till after 6:00 PM.
Mine too. Does anyone know what they do from 9 to 5? Dominick
Looooooong Lunch!!
Quote from: steelhead_killer on May 23, 2016, 09:12:18 PM
West coast delivery times..................... ::)
But I'm on the East Coast (FL.)
Got mine 8) Thanks Alan
Marc..
Mine arrived today and it looks awesome.
Thank you Alan
Mine arrived too, it looks terrific! Can't wait to build another colored 4/0 gem around it... thank you, Alan! :)
~A~
Quote from: David Hall on May 23, 2016, 11:25:55 PM
Thank you Alan
One of your dog spring is not installed the right way.
It should be like this.
(http://i1280.photobucket.com/albums/a494/prochallenger/8726c106-f8d1-4bb2-a87c-0e77250ff984_zpsupr5dtat.jpg)
Got it thanks Alan.
Quote from: David Hall on May 24, 2016, 01:00:30 AM
Got it thanks Alan.
I want to see what Sal would say.
Are you looking at the right side dog spring that is on the end of the dog instead of in the notch?
Or the way the left dog spring is arched under tension?
With the sleeve, washer and gears in place, everything seems to function fine with no interference anywhere.
Dave, the spring on the longer dog should sit in the notch, but if yours is working and you like it, let it go.
I moved it into the notch just so it can be comfortable, but it was working either way.
Just so you know, I inspected the inside cut of the accurate magnum jigmaster side plate. The edges are cut clean and square, radius or eased edges on the bridge will have no effect whatsoever., also the screws stick through the bridge by several threads, this also has no effect, the spool has lots of clearance and nothing is touching. All the test fitting and work you did to help bring this bridge to us is evident, the screw holes lined up perfectly on the magnum plate, better than stock imho. The dogs operate flawlessly and engage the sleeve teeth perfectly simultaneously. It's a work of art. Thanks Sal and thanks Alan.
Thanks Alan...
Delivered to Bay Area by noon Monday... USPS
Beautiful!
Steve
Installed the bridge, and boy does she purrrrrr! Great work! Tolerances are tight! Love it! Bridge screws need to be screwed in a little at a time to line everything up perfect fyi... ;D Thanks Alan!
Mine arrived in today's (5/24/160) mail. Looks GREAT! Hope to put them together later this week. Thanks again Alan.
Regards,
Charlie
The bridge fell right into place with no problems. These parts turned this into a world class reel.
Mike
Received the bridge, looks great. Will add this to the Accurate 4/0 as time allows. Thank you Alan.
I was away over the weekend when my bridge and Lee's lug blanks arrived. I spent a little time installing things last night - the bridge slipped in fine, easier than the Jigmaster bridge of a few months ago, but I had to take a little off the tip of the longer dog, and still need to take a little more off so they will both trip at the same time. I got them closer, but they need just a little more fine tuning. I still need to get an under gear Delrin washer and since my donor was an older open-drag model I need to replace the top hat. Also received the red drag star I ordered, I'm getting close to posting pics of this build....
Sid
I got my double dog bridge yesterday. No time yet to put them together but look top notch. Ken
Sid,
Which gear sleeve did you use?
Mike
Quote from: PacRat on May 26, 2016, 07:05:59 PM
Sid,
Which gear sleeve did you use?
Mike
It is a known info. If the bridge uses with the 8 tooth gear sleeve, the dog will be alternated.
For members on Oahu, Btw..
Brian (@Brian's Fishing) now has the bridges, and sleeves in stock, and available for purchase.
Anyone has a 113H build with this DD bridge installed? Please show a picture......
(http://i1372.photobucket.com/albums/ag355/photoHumboldt/IMG_0499%201_zpszd4ecmpz.jpg) (http://s1372.photobucket.com/user/photoHumboldt/media/IMG_0499%201_zpszd4ecmpz.jpg.html)
Didn't put one together yet with Tom's plates and can't really tell how much those screws are protruding. It would probably be a good idea to shorten the ones marked in Red arrow, the ones marked with Green should be fine.
(http://i1101.photobucket.com/albums/g431/pescatore1/IMG_0499201_zpszd4ecmpz.jpg) (http://s1101.photobucket.com/user/pescatore1/media/IMG_0499201_zpszd4ecmpz.jpg.html)
The Blue arrow is showing the spring sticking up on the eccentric, it will do ok on the 4/0 as is, but on smaller reels it need to sit flush.
You probably already knew this. :)
Sal
I need more bridges!
Caught the spring. Did not shorten bridge screws. No noticeable rubbing on the spool. I have this one set up with a Tib frame and Tib spool. Have not tried with a Newell spool.
Quote from: David Hall on May 28, 2016, 01:44:00 AM
I need more bridges!
Have you called SmoothDrag or Scott yet?
I did thanks
Got the goods on Wednesday. Awesome!
We do have the 113H SS bridges in stock now.
Quote from: Black Pearl on May 28, 2016, 03:35:06 AM
Quote from: David Hall on May 28, 2016, 03:31:43 AM
I did thanks
I thought you bought 4 sets already.
I did but I had four 4/0 reels and three jigmaster magnums!
I've got the same problem. I bought 4 but have 7 or 8 4/0's, 8 Progear's, and a Jigmaster Magnum. I guess I will start with a Progear 454 YTS, a Progear 545, and 2 4/0 Penn YTS reels and go from there. They will have to wait until after a tuna trip Monday and Tuesday.
Haven't installed them yet, but they are a thing of beauty and can't wait to slip them in with the rest of the goodies.
Thanks Alan for getting' er done, and to Sal for the testing to make sure it's perfect.
Dom
Mine are on the way!
Thank you Alan.
I can already tell by the responses I'll need some more ;D
Installed my in Pro Gear 545, since I have 8 tooth sleeve, those double dogs was engaged one the the time which result in less back play and just what I want! ;D
Progress:
(http://i4.photobucket.com/albums/y122/anglingarchitect/IMG_0085_zpsoaulphv9.jpg) (http://s4.photobucket.com/user/anglingarchitect/media/IMG_0085_zpsoaulphv9.jpg.html)
(http://i4.photobucket.com/albums/y122/anglingarchitect/IMG_0092_zpsgsvlkr4f.jpg) (http://s4.photobucket.com/user/anglingarchitect/media/IMG_0092_zpsgsvlkr4f.jpg.html)
So my donor reel has the open drag end plate, somebody on here must need one of these, i need a spacer sleeve, and a nice handle.
(http://i4.photobucket.com/albums/y122/anglingarchitect/IMG_0098_zpsskroiobn.jpg) (http://s4.photobucket.com/user/anglingarchitect/media/IMG_0098_zpsskroiobn.jpg.html)
I installed mine in my PG 545 together with a stainless 10 tooth stud and Bryan's drags. Pretty trick!
My last two 4/0 have the top hat, ordered new sleeves from Scotts, done deal.
There are few sets left for sale in my online store.
Just curious about the make up of these. I dropped one into a ProGear 545 tonite, but was a little reluctant to take out the big beefy SS stock dog I found inside. The two on the PC bridge look so tiny in comparison.
This was tested by Sal and stood up to good pressure right? Not questioning the quality at all, I'm going to be getting more for my Cortez versions too. I have never had a reel blow up on me ever so I'm sure they are up to any test I'd put them thru.
Love that I don't have to do any carving since it just drops in. But they do look small.
A question of theory though; wouldn't the tank with Sal's SS larger double dogs version actually be stronger?
Don't throw lead weights at me. I really am just curious like I said.
I am going to sell some stuff to buy more PC sleeves and bridges so I do trust Alan's productions.
Thanks, Ran
You have good questions Ran. Yes the dogs on the Tank are stronger, but not because of thickness. Those are stronger because of the way they're held in place.
I've asked about the thickness as well in the beginning, Alan assured me that his men had done lots of tests as well and were comfortable with the design.
You will need to take everything in consideration though, the bridge plate on a stock 113H would flex a little when under stress, especially at the numbers that we're getting lately.
If bad enough, it will interfere the gears, yoke and jack as well.
I personally don't believe the aluminum plates help here, still nice to have though.
Most of the stress comes from the bridge post while cranking the handle.
The new custom heat treated bridge, jack and yoke, being heat treated, should help keeping everything aligned there.
I have done lots of stress tests on these, but not on the water.
I personally believe the custom bridge and its dogs will hold up just fine.
By the way, I decided to place the new custom bridge on the Tank, we'll see how that goes.
A lot of work goes into some of these custom parts behind the scene.
When I received the custom bridge, the measurements were spot on with the original bridge, they worked nicely on the Penn stock plates, but not so good on Accurate and some other aluminum plates.
Alan C told me and his men, he needed to make them work on all plates.
After one week of taking 3 different reels apart for at least 60 times each, I was able to come up with the solution.
Lee also had his hands on these parts, I told him I wanted one of the holes sealed on the bridge and I needed it back soon within a week. Lee sent it back within two days and couldn't even tell where the hole was.
I carefully drilled and tapped the new hole and everything lined up nicely from there. By the way, the hole was off only by 1/32" and yet causing problems.
Tolerance is very tight on these, this is a good thing, but at times a little pain to assemble.
Custom parts are usually generated from most of us here.
Along with some others, we have a good product here, I'm sure it will be enjoyed by many in years to come.
Sal
Seeing it go into the tank is great. I really like the way the reel I put the bridge in felt while cranking.
My past on-the-water experience would pale in comparison to Don Dominick's, so I have 100% confidence that I will not ever damage this bridge.
Thanks for the reply.
Quote from: Alto Mare on July 10, 2016, 12:33:29 PMBy the way, I decided to place the new custom bridge on the Tank, we'll see how that goes.
Sal
Sal,
So, what happened with the new bridge in the Tank ?
Tight Lines & Merry Christmas !
Quote from: ez2cdave on December 21, 2016, 04:19:00 AM
Quote from: Alto Mare on July 10, 2016, 12:33:29 PMBy the way, I decided to place the new custom bridge on the Tank, we'll see how that goes.
Sal
Sal,
So, what happened with the new bridge in the Tank ?
Tight Lines & Merry Christmas !
Hello Dave, as far as I know it's still in the Tank and waiting to be used.
Merry Christmas to you as well.
Sal
Few members have been asking me that if this item can back in production.
100 pieces are being made now, but it will take 45 to 60 days.They are all sold to SBT (Scott's Bait & Tackle) 70 pieces and Brian's Fishing Supply 30 pieces.
This item will not be available through PRO Challenger's online store.
The cost of this item has been increased in labor, stainless steel and other materials.
For more info on pre-ordering, please contact SBT or Brian's Fishing Supply.
Thanks,
--Alan
Thank you Alan, I must have another.
Thanks Alan, count me in !!
Ted
You should have ordered more, 100 isn't going to last that long.
Thanks for keeping up with these Alan.
Sal
Would these bridges fit a Pro Gear 440, 545, 454, and 541?
Quote from: Black Pearl on December 28, 2017, 04:27:05 PM
Few members have been asking me that if this item can back in production.
100 pieces are being made now, but it will take 45 to 60 days.They are all sold to SBT (Scott's Bait & Tackle) 70 pieces and Brian's Fishing Supply 30 pieces.
This item will not be available through PRO Challenger's online store.
The cost of this item has been increased in labor, stainless steel and other materials.
For more info on pre-ordering, please contact SBT or Brian's Fishing Supply.
Thanks,
--Alan
Alan,
Please be sure to post here again, when they become available !
Tight Lines !
Quote from: mrwilson99 on December 28, 2017, 10:25:01 PM
Would these bridges fit a Pro Gear 440, 545, 454, and 541?
Yes. I put one in my 545. They all have 4/0 guts.
Quote from: mrwilson99 on December 28, 2017, 10:25:01 PM
Would these bridges fit a Pro Gear 440, 545, 454, and 541?
You can check out this thread http://alantani.com/index.php?topic=16773.msg196076#msg196076 (http://alantani.com/index.php?topic=16773.msg196076#msg196076)
Mr. Wilson,
Cute kid in your avatar, but the word after Newell and Pro Gear doesn't go well with that photo or this site.
Alan,
I could use one or two more. Thanks! I also owe you a phone call. I'll call you tomorrow. My apologies for my tardiness... the crazy days leading up to the holidays and the days after have been nuts.
Thanks
Dom
Here is the latest update on this 113H stainless steel DD bridge. This item will be here on Friday, and it will be distributed to Scott's Bait & Tackle and Brian's Fishing Supply next week. They should have this item on hand by end of next week, and it is up to them when to start selling them. Please contact these 2 retailers for more infomation.
Sweeet !
Thanks Alan !
I'll be placing an order with Scotts
Here are 70 pieces (following pictures) 113H SS double dog bridge to SBT this week.
Another 30 pieces are going to Brian's Fishing Supply tomorrow.
(http://alantani.com/gallery/23/771_29_01_18_8_20_55.jpeg)
That is a beautiful site. Hopefully I can get one in time for my next grouper trip.
Quote from: otownjoe on January 30, 2018, 06:21:47 PM
That is a beautiful site. Hopefully I can get one in time for my next grouper trip.
I think you can call SBT or Brian fishing supply in Hawaii to per order one
SBT doesn't have them in their inventory as of two minutes ago.
Quote from: David Hall on January 30, 2018, 11:21:55 PM
SBT doesn't have them in their inventory as of two minutes ago.
Think Alan said he's shipping today.
Thursday, Friday?
Quote from: David Hall on January 30, 2018, 11:21:55 PM
SBT doesn't have them in their inventory as of two minutes ago.
I am waiting for their reply on which shipping they would like to use.
Thanks,
Alan
Scott's Bait & Tackle started selling this item from its website now.
https://www.mysticparts.com/PennParts/Custom/3-113HPRO.aspx (https://www.mysticparts.com/PennParts/Custom/3-113HPRO.aspx)
Get it while you can. It is going to go fast.
Good luck, guys.
"Edited as per Moderators to correct Scott's Bait & Tackles old online store over to their new store name Mystic Reel Parts / www.mysticparts.com"
Just ordered two.
Ordered mine with the 10 tooth sleeve.
Going to Scott's for one item is like going to Wal Mart.
I spent $300. ::)
Got mine ordered tonight too, along with everything else internal required to build two T4N1 kits. Couldn't believe I'm completely out of 4/0 donor reels? I managed to spend a bit more than you did! Daron Hah! add a couple of Lou's knobs, Ted's Levers, Adams stars, handles and inserts, BP gears and man oh man what a beauty! I can't resist them, it's so much fun collecting all the parts and putting it together. I gotta invest in a display case these are just to pretty to have boxed up in a cupboard.
Quote from: David Hall on February 11, 2018, 06:16:53 AMI gotta invest in a display case these are just to pretty to have boxed up in a cupboard.
Don't forget the "plinth's" . . .
Tight Lines !
Quote from: David Hall on February 11, 2018, 06:16:53 AM
I gotta invest in a display case these are just to pretty to have boxed up in a cupboard.
so, no fishing time for the t4n1 kits?
Lol, I have to build them first, right now I'm getting ready to assemble a couple stock reels with my grandson.
He's building a good ole 65 and I'm putting a stock 10/0 back together. The parts are laid out on the workbench just waiting for him to make the time. He's got school, football and baseball, and Basketball on his agenda along with PS4 so it's a bit of a struggle to get him into the shop without discouraging him. Word is he's been telling his friends at school about the reel so he is interested, he's just slow to get a round tuit!
Like his grandpa. Soon as these are done the T4N1's are next up. Hope to fish mine at the April 1st Morro Bay trip.
Any update on another production run of these? Not surprisingly, everywhere is sold out.
Thanks!
Quote from: C0BRA on March 11, 2018, 04:18:28 AM
Any update on another production run of these? Not surprisingly, everywhere is sold out.
Thanks!
A new production run will be ready in 45 - 60 days.
Thanks,
--Alan
Awesome! Thank you.
Randy had 50 frame kits made and sold out quick. No wonder the dd dog bridges went quick also.
Mike
In for one. Please let me know when the new run comes in.
-gary
A lot of people are looking for this double dog bridge. A new shipment should be ready in about a month to be distributed to SBT and Brain's Fishing Supply.
If some members really need this part, I know that Sal has some on hand. One can check with Sal ASAP.
Sal who? ;)
I'm down for two.
-g
Quote from: Gman_WC on April 05, 2018, 03:14:08 AM
Sal who? ;)
I'm down for two.
-g
This is Sal's profile in this site.
http://alantani.com/index.php?action=profile;u=3274 (http://alantani.com/index.php?action=profile;u=3274)
Thanks. I was jut kidding. We all know who Sal is.
-g
(https://i.imgur.com/sPiJE8N.jpg?1)
Which one's Sal?
:D
Quote from: Gfish on April 12, 2018, 03:33:43 AM
Which one's Sal?
Leave the camera . . . Take the reel - LOL !
Tight Lines !
(https://s3.amazonaws.com/lowres.cartoonstock.com/death-fish-fishing_hook-mafias-mobster-mobs-tton38_low.jpg)
(http://res.cloudinary.com/spontany-com/image/upload/v1512423864/spontany/al-capone-versus-tony-montana-quien-es-mas-macho/pic_109.jpg)
(https://i.pinimg.com/originals/c7/6b/14/c76b146f4f5d551e54c5adf9b59ec102.jpg)
(https://ih0.redbubble.net/image.201981613.4838/flat,750x1000,075,f.u5.jpg)
(https://images.sunfrogshirts.com/2017/02/15/10725-1487220847252-Gildan-Men-Black-_w93_-front.jpg)
(http://rachelscreenprinting.com/wp-content/uploads/2017/04/Saltwater-mafia-skeleton-fighting-chair_Compressed.jpg)
I get excited when I see this thread bumped. I thinking they came back in stock!
-gary
Quote from: Gman_WC on April 13, 2018, 02:40:50 PM
I get excited when I see this thread bumped. I thinking they came back in stock!
-gary
Gary,
Sorry about that . . . Maybe we can get Sal to "make him an offer he can't refuse" ? LOL !
Tight Lines !
**Update-Found it**
Delrin washer. I see all the new kits come with under the main gear washer. Sal was talking about one under the star also.
The only post I've found shows a peel away washer, used for getting correct height. I can't find what i'm looking for even with search
I'm spinning my drag so to speak ;).
Is there a standard or average size anyone is ordering? I'm looking to order a half dozen for jigmaster and 113h.
McMaster-Carr?
Thanks
-gary
Funny stuff Dave. Wonder what kinda rig Al Capone used? I can only see that he's got onea those 1930's 2 guide rods, possibly split bamboo.
Quote from: Gman_WC on April 18, 2018, 03:09:11 PM
**Update-Found it**
Delrin washer. I see all the new kits come with under the main gear washer. Sal was talking about one under the star also.
The only post I've found shows a peel away washer, used for getting correct height. I can't find what i'm looking for even with search
I'm spinning my drag so to speak ;).
Is there a standard or average size anyone is ordering? I'm looking to order a half dozen for jigmaster and 113h.
McMaster-Carr?
Thanks
-gary
Are you needing the Delrin washers for your reels? Send me a `PM with what you need and ill mail them to you.
Keith
Are you needing the Delrin washers for your reels? Send me a `PM with what you need and ill mail them to you.
Keith
[/quote]
PM sent Keith.
Thanks
-gary
Quote from: Gfish on April 20, 2018, 11:11:25 PM
Funny stuff Dave. Wonder what kinda rig Al Capone used? I can only see that he's got onea those 1930's 2 guide rods, possibly split bamboo.
I think Capone's gear was probaly made by Thompson ( "Chopper" model ) . . . He was also known to use equipment made in Louisville, KY ( "Slugger" model ) - LOL !
Tight Lines !
QuoteWonder what kinda rig Al Capone used? I can only see that he's got onea those 1930's 2 guide rods, possibly split bamboo.
Fresh water bait casting tackle from the 1930's. Pflueger stuff more than likely. He is probably fishing in that little lake in his home town.......................<:O)
This item is back in stock in SBT and Brian's Fishing Supply.
Just ordered me one!
Nick
Just a quick note on this item. Mystic ReelParts is running low on this item.
Thanks,
Alan
I cannot connect to MysticParts website at the moment. Can someone tell me the cost of the bridge? Thank you.
Quote from: Bryan Young on July 27, 2018, 05:29:51 PM
I cannot connect to MysticParts website at the moment. Can someone tell me the cost of the bridge? Thank you.
$54.99
Thank you.
Are these in stock anywhere or is there any word on when they might be?
Thanks,
Mike
If any one has them I've not found them & I've spent some time looking... Jeff
QuoteIf any one has them I've not found them & I've spent some time looking... Jeff
I was afraid of that. Thanks Jeff!
Mike
You didn't look far enough. https://www.mysticparts.com/Custom/ProChallenger/3-113HPRO.aspx (https://www.mysticparts.com/Custom/ProChallenger/3-113HPRO.aspx)
Joe
Fixed link for MRP ~Mo
Joe, it's out of stock. Says so.. Jeff
That was the first place I looked Joe. Thanks though!
Oups :-[ I didn't see that ::) ::) :-X Open mouth insert foot ;) ;D.....................Joe
Mystic order 100 pieces of this DD bridge. It should be done in a month.
Sweet! Thanks Alan!
Yahoo !!!!!!!!!
This is good. Very good... Jeff
I'll take the credit for bring it up. ;D ;)... I'm glad it worked out guys.................Joe
Awesome BP, I'll be needing 4 of them when they're ready. I believe I bought their last two about a month ago ;D
QuoteI believe I bought their last two about a month ago Grin
So it's YOUR fault!
hahahaha
Quote from: Fishy247 on October 26, 2018, 08:02:27 PM
QuoteI believe I bought their last two about a month ago Grin
So it's YOUR fault!
hahahaha
I guess so, but my reels are purring though ;D
The bridges that Mystic were selling had been repaired. They welded the screw hole and drilled and tapped them. The problem is the heat treatment in that area is gone. The new ones are going to be correct.
Mkke
Quote from: mikeysm on October 28, 2018, 01:15:38 PM
The bridges that Mystic were selling had been repaired. They welded the screw hole and drilled and tapped them. The problem is the heat treatment in that area is gone. The new ones are going to be correct.
Mkke
Mike, I just want to make sure I get the correct information from you. this would be for me and the members here.
Did the fixed bridge fail you? Could you post some details?
I tested these afterwards and couldn't report any issues, if you did, it would be helpful hearing about it.
I'm actually the guy that found the misaligned hole on the very first batch a long time ago. Unfortunately, they used the wrong information from that older email...it happens.
I think they did a good job making it right, as far as alignment.
Thanks,
Sal
Im not going to get into to that. I bought two of them thinking that were new not reconditioned. Its up to the person if they want to take a chance or not. But at least let them know what they are buying.
Mike
Quote from: mikeysm on October 28, 2018, 01:57:38 PM
Im not going to get into to that. I bought two of them thinking that were new not reconditioned. Its up to the person if they want to take a chance or not. But at least let them know what they are buying.
Mike
I did post a thread about it last June when day one had the issue.
http://alantani.com/index.php?topic=25455.msg288925#msg288925 (http://alantani.com/index.php?topic=25455.msg288925#msg288925). Regardless, it was my bad, but those bridges were new and never been used. It will not fail.
Quote from: mikeysm on October 28, 2018, 01:57:38 PM
Im not going to get into to that. I bought two of them thinking that were new not reconditioned. Its up to the person if they want to take a chance or not. But at least let them know what they are buying.
Mike
I didn't really get back the answer to my question to you.
I do not have anything to do with your buying experience, I was simply asking if the bridge..as you have it now...has failed you, as for functionality and not appearance.
About other comments you've put out, that would be something you would need to discuss with the gentlemen that sold those to you.
Sal
They are going back.I am not going to use them.
Mike
Quote from: mikeysm on October 28, 2018, 02:19:45 PM
They are going back.I am not going to use them.
Mike
I thought you used them :-\. Ok...got it!
Mike: With all due respect. In My opinion you should thake that issue up with the seller to give them a chance to make it right. Sal is interested in learning if the bridges were in any way defective as we are on the AT site.
To bring something up that you imply someone misrepresented a part and not give through redemption a chance, well in my book. It's a one way street your living on.
This post is not made to embarrass or disrespect Mike I'm sure he has a right to voice his opinion and he does. This is just my opinion......................Joe
i would ideally like this issue to be settled short term in a calm and professional manner. long term, i will be speaking to all parties in about a month, some over the phone but preferably in person over a single malt. i have several concerns, but they will have to wait until things are taken care of on the home front. until then, gentlemen........
The bridge I have fits the description of what's being described.
This bridge has been removed from the reel repeatedly & tightened down " Tight " with zero issues.
For any new guys here. The guys that sell stuff here are stand up, take care of things type fellas.
Every one of them best I can tell wants to sell you a good product. They also wish to know of any issues.
Some of these fellas have regular jobs. They just aint making a killing on producing this stuff for us.
I for one choose to be understanding & have patience with all this in mind... Jeff
I'll take one from the new batch as well... along with SS Gear Sleeve. Next is a Aluminum frame and spool!
This item is available at Mystic reel parts now.
Thanks,
Alan
Quote from: Black Pearl on January 27, 2019, 05:41:27 PM
This item is available at Mystic reel parts now.
Thanks,
Alan
Thanks Alan.
I just hit Mo up for four bridges. Get'm while you can! :o
Two new XN T4N1Tib's to build and upgrading two
Tib narrows getting full ss guts.
-g
Hi guys, I'm putting together Alan's bridge and good thing I looked here. Was wondering why it was so hard to turn the handle.
1) Need to sand down the back side of the Smooth Drag SS yoke
2) The Pro Challenger SS eccentric plate leading edges need to be sanded down just a bit too? Please see pic and correct me if I'm wrong about the location (arrows)
Hello Jkel, I'm not sure I follow what you are saying.
I think you are saying that after installing the custom jack and custom yoke the handle was hard to turn?
But after you sanded the jack, as you're showing on your pic everything is fine now?
Just wanted to make sure I got it right.
Thanks,
Sal
Yes after installing the SS jack and SS yoke the handle was hard to turn.
I sanded down the SS yoke a little and the handle did turn a bit better but not by much. I even swapped the SS yoke with the stock brass and it turned slightly better but not by much. It's nowhere near how a stock setup feels.
Then I read that the SS jack leading edges needed to be sanded down a bit too? Haven't done that yet so wanted to verify.
Funny, I'm putting together a custom build and I can't even get the new SS Jack\Yoke to fit in\on the Eccentric It just does not seem to fit.
I cussed till 2am Sunday night and gave up.
I know one side of the yoke is flat and the other not that goes up.
-g
Hmmm I'm using the stock 113 sideplate and everything fits. Are you using custom aluminum sideplates?
Quote from: jkel on February 14, 2019, 04:37:38 AM
Hmmm I'm using the stock 113 sideplate and everything fits. Are you using custom aluminum sideplates?
Yes, Cortez New 113h
(http://alantani.com/gallery/24/13259_08_08_18_3_51_29.jpeg)
Everything stainless I could find and it all fits with no issues. Tiburon frame and original side plates.
Jkel- I installed the same bridge and SS yoke/jack into stock plates and it sounds like I had a similar issue. What I found is that the new bridge has very tight tolerances, whereas the stock plates are very loosey-goosey. Everything can seem to line up without a problem, but when you tighten it up, getting in and out of gear is a chore, as well as cranking. I found that the bridge has to be lined up just so, otherwise, these issues continue. Try making sure that that top edge lines up parallel to the corresponding ridge on the plate. On mine, it sat just below it, maybe 1/32" or so. If it was more than that or if it wasn't parallel, it would bind up. This is what the instructions were talking about when they said to tighten it up a little at a time.
Good luck and let us know how it goes!
Mike
There are many of these reels out there doing just fine. Check your assembly again.
Sanding down parts as you did wouldn't do anything to the reel, there is already enough clearance there. But if it makes you feel better, why not.
Try tightening the bridge screws a little at a time, this should be done as such on all reels and not just the 113H.
Sal
I feel your pain,many almost put themselves together and once and awhile one that just doesn't seem to fit. Keep at it, it will work.
Quote from: Swami805 on February 14, 2019, 09:26:27 PM
I feel your pain,many almost put themselves together and once and awhile one that just doesn't seem to fit. Keep at it, it will work.
And if it still doesn't, we'll make sure it will. :)
Mike, Sal, I want to thank you for your advice and I'll give it a go this weekend and report back. ;D
And yes Swami805 I will keep at it until I get it working right!
These reels have parts kits made from 3-4 different vendors, it is expected to do a little minor adjustment here and there.
I have no doubts you will get it, but just in case you don't, you have nothing to worry about.
Sal
After making sure everything was properly positioned and tightened down correctly the handle was still hard to turn. Could not think of anything else and then it hit me....'swap out the SD Carbontex kit with Bryan's drag kit'.
Out with the SD kit and in with Bryan's kit. Wow I couldn't believe how much of a difference it made. The handle turned just as smoothly as stock! I did have to file the 'ears' down just a bit on those metal washers to get them to fit properly in the PC main gear. Other than that it's good to go!
Seems like the Smooth Drag Carbontex drag kit doesn't mesh well with the Pro Challenger main gear?? I was using that drag kit with the stock main gear and it worked just fine.
But anyway thanks again to all! ;D
It sounds like your drag stack was to tall. Sometimes you have to adjust the stack height by using thinner or thicker metal washers. Or it could be incorrect parts above the stack. Maybe if you had just removed the delrin washer from under the main gear & replaced it with the original fiber washer it all might have been fine. When modifing these reels with custom parts a caliper is your friend. Rudy
Well shoot! I'm glad you got it figured out. Now git out there and catch something on it! ;D
Quote from: RowdyW on February 16, 2019, 10:40:18 PM
It sounds like your drag stack was to tall. Sometimes you have to adjust the stack height by using thinner or thicker metal washers. Or it could be incorrect parts above the stack. Maybe if you had just removed the delrin washer from under the main gear & replaced it with the original fiber washer it all might have been fine. When modifing these reels with custom parts a caliper is your friend. Rudy
That's one tool I don't have and should look into. :)
Quote from: Fishy247 on February 16, 2019, 11:44:08 PM
Well shoot! I'm glad you got it figured out. Now git out there and catch something on it! ;D
You're absolutely correct so now it's time to spool the reel with 60lb mono! ;D