Reel Repair by Alan Tani

Spinning Reel Rebuild Tutorials and Questions => Shimano => Topic started by: Meh? on October 13, 2012, 02:59:17 AM

Title: Shimano Stella 2000 Rebuild/Repair
Post by: Meh? on October 13, 2012, 02:59:17 AM
I posted this on another forum a year or so ago, thought you guys might find it helpful.

After owning this reel for a little over a year I decided it was time for a service.
So here goes...

Note: the 2000 size Stella shares the same body as the 2500 some parts in the reel besides the rotor are available from Shimano Australia.
Shimano didn't tell me this but were otherwise very helpful and the parts I ordered showed up very quickly.

First remove the spool to expose the spool bearing assembly.
(http://img.photobucket.com/albums/v37/n000b/P1000467.jpg)

To get the assembly off remove the the spool washers and then wind out the small grub screw. I didn't have the correct size allen key handy so i used a pair of fine tweezers to wind it out.
(http://img.photobucket.com/albums/v37/n000b/P1000469.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000470.jpg)

Remove the rotor nut lock plate.
(http://img.photobucket.com/albums/v37/n000b/P1000471.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000475.jpg)

Undo the rotor nut remembering that it is a REVERSE THREAD to undo it you must turn it in a clockwise direction.
This is best done with a socket, you can do it with a small shifter provided you are careful.
(http://img.photobucket.com/albums/v37/n000b/P1000472.jpg)

You can now remove the rotor assembly.
(http://img.photobucket.com/albums/v37/n000b/P1000476.jpg)

Next remove the roller clutch waterproof retainer and spool support.
(http://img.photobucket.com/albums/v37/n000b/P1000477.jpg)

Be careful with the seal and spacer.
(http://img.photobucket.com/albums/v37/n000b/P1000479.jpg)

Very carefully remove the roller clutch assembly, there are 6 tiny springs and a washer that you really don't want to lose .
(http://img.photobucket.com/albums/v37/n000b/P1000478.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000480.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000481.jpg)

Undo the bearing retainer screws and take off the retainer.
(http://img.photobucket.com/albums/v37/n000b/P1000483.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000484.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000485.jpg)

Remove the Anti reverse spring and guide. Be careful with this it will shoot out and believe me you wont find it.
(http://img.photobucket.com/albums/v37/n000b/P1000487.jpg)

Slide out the pinion gear and bearing.
(http://img.photobucket.com/albums/v37/n000b/P1000486.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000489.jpg)

Take off the friction ring and remove the friction ring spacer to access the side plate screws.
(http://img.photobucket.com/albums/v37/n000b/P1000491.jpg)

Remove the body flange seal to access the rear protector screw.
(http://img.photobucket.com/albums/v37/n000b/P1000492.jpg)

Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: Meh? on October 13, 2012, 03:00:17 AM
(http://img.photobucket.com/albums/v37/n000b/P1000493.jpg)

Remove the rear protector and shield.
(http://img.photobucket.com/albums/v37/n000b/P1000494.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000495.jpg)

Undo the side plate screws and take off the side plate.
(http://img.photobucket.com/albums/v37/n000b/P1000496.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000497.jpg)

Note the side plate seal.
(http://img.photobucket.com/albums/v37/n000b/P1000529.jpg)

Take out the drive gear. Note the location of the washer.
(http://img.photobucket.com/albums/v37/n000b/P1000499.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000498.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000501.jpg)

Take out the rear protector collar and screw.
(http://img.photobucket.com/albums/v37/n000b/P1000502.jpg)

Undo the oscillating slider, slide off the lower pinion gear bearing.
(http://img.photobucket.com/albums/v37/n000b/P1000503.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000504.jpg)

Take off the oscillating pawl cover and take out the pawl assembly. (I didn't get a photo of the full assembly. Check the schematic)

Take off the worm screw retainer (be careful there is a tiny washer under it.)
(http://img.photobucket.com/albums/v37/n000b/P1000505.jpg)

Slide out the two oscillating guides.
(http://img.photobucket.com/albums/v37/n000b/P1000506.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000507.jpg)

About a year ago i dropped the base of the reel in some wet sand and some corrosion has started. (I will show the repair at the end of the post.)
(http://img.photobucket.com/albums/v37/n000b/P1000508.jpg)

Slide out the main shaft. All parts are not shown.
(http://img.photobucket.com/albums/v37/n000b/P1000509.jpg)

Should look like this.
(http://img.photobucket.com/albums/v37/n000b/P1000511.jpg)
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: Meh? on October 13, 2012, 03:01:14 AM
Push out the worm shaft then take out the idle gear, not a complete photo but its fairly obvious once you start.
(http://img.photobucket.com/albums/v37/n000b/P1000512.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000513.jpg)

Ok, now comes the time to put it all back together.

The assembly will mostly be photos as it is essentially the reverse of what has just been explained.

Start by cleaning all parts (bearings, gears etc.) thoroughly with Carburetor cleaner if you don't have this you could use another suitable solvent. An ultrasonic cleaner would be even better.

Using some heavy non water soluble grease to coat the inside of the reel. I used Cals drag grease
(http://img.photobucket.com/albums/v37/n000b/P1000518.jpg)

Oil all bearings before re-assembly. I used Shimano oil with a few drops of hot sauce oil. I didn't use hot sauce straight because although it is suited for spool bearings on bait casters IMO it is too thin for this application.
(http://img.photobucket.com/albums/v37/n000b/P1000519.jpg)

I used hot sauce grease on all gears.
(http://img.photobucket.com/albums/v37/n000b/P1000522.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000520.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000523.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000525.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000527.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000529.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000530.jpg)

I grease the threads on all external screws.
(http://img.photobucket.com/albums/v37/n000b/P1000531.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000532.jpg)

I also greased under the rear protector to help prevent corrosion occurring again.
(http://img.photobucket.com/albums/v37/n000b/P1000534.jpg)

The old rear protector was a little scratched so I ordered a new one (same as 2500 Size)
(http://img.photobucket.com/albums/v37/n000b/P1000546.jpg)

(http://img.photobucket.com/albums/v37/n000b/P1000535.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000536.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000541.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000543.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000545.jpg)
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: Meh? on October 13, 2012, 03:02:09 AM
(http://img.photobucket.com/albums/v37/n000b/P1000548.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000549.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1000550.jpg)

The body is complete, you may want to check the rotor assembly I didn't feel the need, I did clean and re oil the line roller bearings and carriers.
This photo is not the correct order, check the Schematic.
(http://img.photobucket.com/albums/v37/n000b/P1000551.jpg)

Finished
(http://img.photobucket.com/albums/v37/n000b/P1000554.jpg)
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: Meh? on October 13, 2012, 03:05:56 AM
Corrosion Repair
About a year ago I dropped the base of the reel into some wet sand.
The sand and salt found its way through the two drainage holes in the rear protector.
(http://img.photobucket.com/albums/v37/n000b/P1000516.jpg)

I had intended to clean this out but it slipped my mind meaning that the salt and sand rattled around i the small cavity and eventually the inevitable happened.
(http://img.photobucket.com/albums/v37/n000b/P1000508.jpg)

The internals of the reel were still in prefect condition no sand or other material has got in, if the corrosion was allowed to continue it would have become a problem.

Firstly I extremely lightly ground away the corroded material until the intact magnesium was exposed.

I used a diamond bit in a dremel set on the lowest speed.
(http://img.photobucket.com/albums/v37/n000b/1311053702857.jpg)

After grinding the affected area and the edges of paint surrounding it was  was lightly sanded then cleaned with wax and grease remover.
(http://img.photobucket.com/albums/v37/n000b/1310955974232.jpg)
(http://img.photobucket.com/albums/v37/n000b/1310956046681.jpg)

I then coated the sanded area with a high strength 2 part epoxy. Araldite wont cut it.
(http://img.photobucket.com/albums/v37/n000b/1311053317316.jpg)

Because the inner bearing surface was affected I could not just coat it with epoxy and let it cure as the bearing would no longer fit, and even if i sanded it back it would be impossible to get perfect and the alignment would be thrown out.

The solution I came up with was to use a drill bit as a reverse mold/alignment tool of sorts.

Drill bits are made to precise tolerances and once the epoxy has cured around it a perfect surface will be left behind.

The bearings on either end of the worm shaft are 6mm so I used a 6mm drill bit.

To prevent the epoxy permanently attaching the drill bit to the body it needed to be coated with something to stop it sticking.

I used some mold release and then dipped it in PVA. This is how boat builders prevent fiberglass sticking to their molds.
I was a little worried this method would increase the diameter of the drill bit enough to result in a poor fit, this was not the case it was a perfect fit.
You must let the PVA dry first.
(http://img.photobucket.com/albums/v37/n000b/1311054095229.jpg)

The drill bit used was a new 6mm Sutton. The shank (smooth part) was just long enough to reach between the upper and lower bearing housings to allow perfect alignment between the two.
(http://img.photobucket.com/albums/v37/n000b/1310957037119.jpg)
(http://img.photobucket.com/albums/v37/n000b/1310957114858.jpg)

After the epoxy had cured I gently twisted the drill to break it free and slid it out.
I then cleaned out the hole to remove any mold release. Sanded back the epoxy flush with the original surface with a flat jewelers file and 400 sand paper then thoroughly cleaned the entire body.

Then it was ready for re-assembly.

Wrong side, but you get the point.
(http://img.photobucket.com/albums/v37/n000b/P1000534.jpg)
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: Meh? on October 13, 2012, 03:07:18 AM
Its been a bit over a year since the rebuild and the reel is still going well, or so I thought.

Corrosion has started in a new area and I'm not happy about it.
(http://img.photobucket.com/albums/v37/n000b/Stella%20Rebuild/20121005_002.jpg)

You can see from the photo where the first repair was done and it is in a completely separate area. Believe me I checked (literally with a magnifying glass) and it was not there when I rebuilt it the first time.

This reel has been looked after very carefully, rinsed after each use and dried off.

For an $800 (at the time) reel that is supposedly salt safe this is not good enough, especially considering that it has been used less 10 times since the service I did.

If you own one of these reels I suggest you check it out. This is a real shame because I have always believed that stellas were superior to the exist, especially in terms of reliability and build quality.

To be fair the reel still works exceptionally but if this corrosion after only a year of very light use is allowed to continue the reel will be ruined.
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: Cone on October 13, 2012, 03:22:26 AM
Thank you for the post. Good info and very clear.  Bob
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: redsetta on October 13, 2012, 05:34:56 AM
x2 - thanks Meh.
Planned obsolesence is an inevitable and natural part of the industry's business model - all the more so in the modern context.
Albert made a great summary of this some time back.
As with capt's post yesterday, it can be both disappointing and costly.
Managing our expectations as end users is kinda tough, but clearly important.
Thanks for the post.
Cheers, Justin
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: Meh? on October 13, 2012, 06:40:36 AM
I wouldn't put this one down to planned obsolescence, I think it may be a manufacturing fault. I have an FE4000 which has had some hard use in tropical Australia with no corrosion issues. I have also had an FD 2000 and FD 1000 which also had no issues. Im thinking I may have been unlucky and the protective coating on this particular reel is defective in the affected area.
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: redsetta on October 13, 2012, 08:31:15 AM
Fair enough - 'twas more a general observation.
Good work on the fix.
Cheers, Justin
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: alantani on October 19, 2012, 12:21:15 AM
thank you very much!
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: johndtuttle on October 19, 2012, 12:58:29 AM
Hi Meh,

Thanks for the fine post and very cool repair.

Sorry it was necessary. The Stella FE is a magnesium body and frame for lightness and is not intended for salt water as I believe you have found. Not to say you can't make it work with extra vigilance but that is just about the last material one would choose for a salt water reel as it is so reactive. I have 2 Stella SW so I can certainly appreciate them overall, but that series has materials chosen that are more ideal plus other sealing etc. to make them arguable the finest you can get.

best regards and thank again for the fine post.
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: Meh? on October 19, 2012, 07:54:34 AM
It is advertised as a salt water safe reel, and in all my past experiences with magnesium reels (stellas, exists etc) I have not had a problem. I am going to check out an identical reel tomorrow that has equal if not more use than mine.

I am very interested to see how it has held up.
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: johndtuttle on October 19, 2012, 04:42:03 PM
Quote from: Meh? on October 19, 2012, 07:54:34 AM
It is advertised as a salt water safe reel, and in all my past experiences with magnesium reels (stellas, exists etc) I have not had a problem. I am going to check out an identical reel tomorrow that has equal if not more use than mine.

I am very interested to see how it has held up.

Yes, you are correct and I checked ShimanoUSA's website that does state that the Stella FE are approved for Salt Water (goes to show what I know :)). As previously observed that area of the reel is particularly vulnerable spot for sequestering salt water.

Shimano USA's Platinum service may have replaced the body at no charge other than their $30 service fee, I have had them do similar on a reel foot I snapped.

best, and thanks again for the post.
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: Meh? on October 28, 2012, 03:28:23 AM
Repair number two:
(http://img.photobucket.com/albums/v37/n000b/P1100324.jpg)

Ground back.
(http://img.photobucket.com/albums/v37/n000b/P1100330-1.jpg)

Finished:
(http://img.photobucket.com/albums/v37/n000b/P1100647.jpg)

Previous repair has held up well, no corrosion at all.
(http://img.photobucket.com/albums/v37/n000b/P1100328.jpg)


Ceramic bearing upgrade:

Upgraded a friends reel with ceramic bearings on the drive gear and line roller. Interestingly enough this reel has had more use than mine, on a boat getting salt spray all over it. It has no corrosion at all.
(http://img.photobucket.com/albums/v37/n000b/P1100630.jpg)

2000 Stella bits everywhere.
(http://img.photobucket.com/albums/v37/n000b/P1100632.jpg)

Bearings
(http://img.photobucket.com/albums/v37/n000b/P1100631.jpg)

Installed
(http://img.photobucket.com/albums/v37/n000b/P1100634.jpg)

Also played around with washer thicknesses on the drive gear to remove some of the handle play 0.05mm makes a big difference.
(http://img.photobucket.com/albums/v37/n000b/P1100637.jpg)
(http://img.photobucket.com/albums/v37/n000b/P1100636.jpg)
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: johndtuttle on October 31, 2012, 05:06:45 PM
cool mate, thanks for the post.  :)
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: Killerbug on October 31, 2012, 09:43:50 PM
Thanks for a helpfull tutorial, nice to fall back on, when I get an exploded Stella 2000 in front of me.
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: jjunck on April 22, 2014, 09:25:35 AM
Very nice presentation.  I will also reference this in the future.  I appreciate the tips on corrosion repair, as well.  I do not have much experience with this. 
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: DavidKa on July 12, 2016, 10:11:32 PM
I have 09 Exsence that has a very similar Mg body to the Stella.
Would you advise sealing these rear protector holes? Or it can cause condensation problems?
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: Frankyreel on May 16, 2019, 12:35:14 AM
Hi, it's a very good job, you really helped me, thanks, really really thanks

Frank
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: Beatnut78 on August 01, 2021, 02:26:21 AM
Brilliant thread! It really taught me a lot.

10/10 Meh?! You're the MVP!
Title: Re: Shimano Stella 2000 Rebuild/Repair
Post by: Donnyboat on August 01, 2021, 11:31:32 AM
Yes x2, cheers Don.