alan tani @ alantani.com fishing reel repair rebuild tutorial Cleaning Accurate Anti-reverse bearings
Reel Repair by Alan Tani
March 31, 2020, 11:30:29 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Search Login Register  
Pages: 1 [2]   Go Down
  Print  
Author Topic: Cleaning Accurate Anti-reverse bearings  (Read 37913 times)
0 Members and 1 Guest are viewing this topic.
Bryan Young
Ultimate Upgrades Drags
Administrator
Member
*****
Online Online

Posts: 10343


The Reel Whisperer


« Reply #15 on: February 01, 2012, 09:15:03 PM »

Chinese ointment contains turpentine, so, anything goes I guess.
Logged

Cheesy I talk with every part I send out and each reel I repair so that they perform at the top of their game. Cheesy
redsetta
Moderator
Member
****
Offline Offline

Posts: 2784


Auckland, New Zealand


« Reply #16 on: February 01, 2012, 09:16:55 PM »

Quote
bit like my dad,smokin killed him.they dont muck around at the cremetorium
Too funny Wallace - you crack me up.  Wink
Logged

Fortitudine vincimus - By endurance we conquer
David Hall
Firearms Group
Member
**
Online Online

Posts: 3610



« Reply #17 on: November 22, 2014, 10:57:16 PM »

What?
The spool can go in backwards?
*#^%++^{^*##„
Ah heck!
I guess if you don't take the reel apart and put it back together at least ten times you just don't know the reel well enough.
And I was so efficient I didn't need all the parts to put it back together!
I think I'll sell them on EBay.
Logged
David Hall
Firearms Group
Member
**
Online Online

Posts: 3610



« Reply #18 on: November 22, 2014, 11:05:17 PM »

Here's a legitimate question.
I cleaned and lubed my ARB's with cals grease packed it in good too!
Do I now need to go back in and clean it out and re lube with corrosionX?
Kinda did something similar with my tekota, I had it back together and thought I might take the spool tensioner cap off and check it out.  It looked like it had been packed with grease at one time, so I filled it up with cals and screwed it back on.  took it off again to take another look at it and most of the grease had been forced down into the side plate.
Wondering if I am going to cause myself trouble with this too?
Logged
alantani
admin
Administrator
Member
*****
Online Online

Posts: 18245



« Reply #19 on: November 22, 2014, 11:25:04 PM »

grease in the AR bearings can be a problem, so i generally recommend a light oil.  in general AR bearings are finnicky.  they're like a girlfriend that cheats on you. if they fail once, they can never be completely trusted again. 
Logged

send me an email at alantani@yahoo.com for questions!
David Hall
Firearms Group
Member
**
Online Online

Posts: 3610



« Reply #20 on: November 23, 2014, 12:12:35 AM »

 Cool open up I'm going back in!
Logged
al_n_VB757
Member
*
Offline Offline

Posts: 22


« Reply #21 on: January 21, 2015, 09:54:09 AM »

grease in the AR bearings can be a problem, so i generally recommend a light oil.  in general AR bearings are finnicky.  they're like a girlfriend that cheats on you. if they fail once, they can never be completely trusted again. 
hahah!!! need to find a better girlfriend!
Logged
Tiddlerbasher
Photo Group
Member
**
Online Online

Posts: 2871



« Reply #22 on: October 26, 2015, 08:05:17 AM »

I now only use IPA (very occasionally acetone) for cleaning bearings. Pop the bearing into a small glass jar - cover with IPA. Place the glass jar in an el cheapo ultrasonic cleaner. Fill the cleaner with hot water (to above the IPA level) - 2-3 mins. Empty jar and refill with IPA - another 2-3 mins - job done. If it's an ARB I generally lube with CorrosionX or TSI321. Some ARBs are fussier than others. If the bearing is already rusty - replace it.
Logged
Gfish
Gfish
Member
*
Online Online

Posts: 2387


What? Me worry?


« Reply #23 on: September 02, 2017, 09:31:06 PM »

Finally got tired of a "stiff" cranking feel for my DPX2. Oiling it through the port didn't help that much. So I stripped almost everything off the head-plate, put a cork in the crank/ARB shaft hole, balenced the plate so the hole was vertical and sprayed Inox into it, until the bearing was fully submerged. Lots a bubbles! Drain, repeat, and after twisting a paper towel in there, some ReelX(comes in the box with the reel). Much better.
Gfish
Logged

Fishing tackle is an art form and all fish caught on the right tackle are"Gfish"!
johndtuttle
Sensei
Member
***
Offline Offline

Posts: 1922


« Reply #24 on: September 03, 2017, 11:26:30 AM »

Accurate uses Cal's cut with Corrosion-X last I talked to Ben.
Logged
Pages: 1 [2]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Simple Audio Video Embedder
Valid XHTML 1.0! Valid CSS!
Page created in 0.2 seconds with 18 queries.