alan tani @ alantani.com fishing reel repair rebuild tutorial Tanacom 750 Service
Reel Repair by Alan Tani
March 31, 2020, 11:48:12 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Search Login Register  
Pages: 1 [2]   Go Down
  Print  
Author Topic: Tanacom 750 Service  (Read 15863 times)
0 Members and 2 Guests are viewing this topic.
ericl1947
Member
*
Offline Offline

Posts: 2


« Reply #15 on: August 13, 2018, 10:36:24 PM »

Hi and thanks for the great post.
I have a Tanacom Bull 1000 and the anti reverse has stopped working. Would you know if your tutorial is close enough to use for my Tanacom Bull
Regards
Eric
Logged
Bloggsy
Member
*
Offline Offline

Posts: 10


« Reply #16 on: September 07, 2018, 01:43:33 PM »

I used this tutorial to assist me in stripping down my 2 Tanacom 1000 and after ordering bearings & O rings it was a a couple of months before I got back to reassemble. I have forgotten where one washer goes. They were next to the Drag collar A but I cant find this washer listed in the schematics or any on line tutorial. I have attached photos where I believe it may go but would appreciate some help as to whether I am right or not. The washer is 11.9mm o.d. x 8.13mm i.d. x .96mm thick and it fits over the drive shaft nicely and into the recess of the Drag collar

Thanks
Bloggsy


* Washer.jpg (63.39 KB, 481x640 - viewed 122 times.)

* Drag collar recess.jpg (75.73 KB, 640x480 - viewed 130 times.)

* Location.jpg (69.57 KB, 640x480 - viewed 141 times.)

* Drag collar.jpg (97.72 KB, 640x480 - viewed 133 times.)
Logged
PipeJumper
Member
*
Offline Offline

Posts: 1


« Reply #17 on: September 17, 2018, 07:40:33 PM »

I have the same extra part and I believe it goes between 89 and 105.  Probably added later since 105 could dig into the plastic when folks crank down the drag.

I never noticed it fit that collar but I happen to have one dissembles so took a look at it. It does fit but sticks out a little which would impact the drag pressure so Iím fairly certain it doesnít go there.

First time I tore mine a part I was stumped on the extra part too. I havenít had issue with the reel having it between 89 and 105 but maybe Iíve done it wrong all these years.
Logged
Bloggsy
Member
*
Offline Offline

Posts: 10


« Reply #18 on: September 17, 2018, 08:13:24 PM »

Thank you so much for the reply yes the only concern that I had with my suggested placement was that it stuck out a bit and didn't allow for full face contact on the drag washer, here is a reply I received from another member Rothmar2:

Yes I have done a few of these, but it was quite some time ago. I think from the pictures you have up, that looks about right. I think the shims you have shown go under the drag sleeve/collar, to stop the drag star from bottoming out and rubbing against the plastic side cover. I could get a reel back to check, but it might take me a few days, as I donít own one. Does the reel function OK with the shim located as you have shown, when fully assembled?

So now I don't know which way to go, it's very annoying when parts aren't shown on the schematics because you always think well I have the diagram in case things go wrong but not so in this case. I can only hope to hear back from Rothmar2 or from someone who has done a few as I hate to reassemble things wrong.
I did contact Daiwa here in Australia but they declined to answer (they probably think that you should be sending it to them for repair) 

 
Logged
Bloggsy
Member
*
Offline Offline

Posts: 10


« Reply #19 on: September 19, 2018, 02:16:10 PM »

I still have no definitive answer on this washer issue surely someone has had these apart? All I can assume is that it was a later addition/upgrade. Daiwa have not replied to any of my emails I have attached some more photos of possible location.


* Schematic drag collar20180918_21331657.jpg (757.51 KB, 3578x2073 - viewed 145 times.)

* Location 1.jpg (81.96 KB, 640x480 - viewed 140 times.)

* Location 2.jpg (77.59 KB, 640x480 - viewed 143 times.)
Logged
Redzwulf
Member
*
Offline Offline

Posts: 13



WWW
« Reply #20 on: February 18, 2019, 07:44:15 PM »

Sorry, hadn't seen this until now.

The washer goes in location 2.

Regards,
Eric
Logged
WalterWyman
Member
*
Offline Offline

Posts: 31



« Reply #21 on: July 03, 2019, 06:28:39 AM »

I am having a problem as I canít see the pictures of the reel am I doing something wrong or did they disappear? I now have one on my bench and this would be awesome not to do it blind!

Thanks
Wally
Logged

"You said the grinding sound just started after leaving it sit wet for 1 year?" I see.....
Donnyboat
donnyboat
Photo Group
Member
**
Online Online

Posts: 1645


« Reply #22 on: July 03, 2019, 07:33:55 AM »

Wally, take digital photos as you go, step by step, them follow them as you place it back together, you should by good, cheers Don.
Logged

Don, or donnyboat
Redzwulf
Member
*
Offline Offline

Posts: 13



WWW
« Reply #23 on: July 05, 2019, 05:41:03 AM »

https://www.facebook.com/pg/RougarouRods/notes/?ref=page_internal
« Last Edit: July 05, 2019, 05:47:09 AM by Redzwulf » Logged
Pages: 1 [2]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Simple Audio Video Embedder
Valid XHTML 1.0! Valid CSS!
Page created in 0.195 seconds with 18 queries.