alan tani @ alantani.com fishing reel repair rebuild tutorial Sealine x40HA questions
Reel Repair by Alan Tani
March 19, 2019, 07:16:55 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Search Login Register  
Pages: [1] 2   Go Down
  Print  
Author Topic: Sealine x40HA questions  (Read 570 times)
0 Members and 1 Guest are viewing this topic.
Mrc70
Member
*
Offline Offline

Posts: 29


« on: January 11, 2019, 10:16:19 PM »

Hello!  What a great website!  Can someone please answer two novice questions ?  I am servicing my Sealine x40HA and before I proceed with the channel locks  Cheesy I would like to know:

Key 78- i cannot get this off the spool axle. is this stuck to the spool? I assume the answer is “yes.”

Key 20- I cannot get this off the spool axle!  it is indeed supposedto come off, correct?

I have attached pictures for your viewing enjoyment  Cheesy.

Thank you!


* 7F82D914-A5F7-410F-9ADF-D0735B2E9508.jpeg (1802.66 KB, 4032x3024 - viewed 17 times.)

* 10FDD081-6503-4E91-B595-BC4C1D7F1D0F.jpeg (1751.68 KB, 4032x3024 - viewed 11 times.)

* 29DB905F-F880-4A0C-8724-58114369F8FE.jpeg (1857.06 KB, 4032x3024 - viewed 9 times.)

* DF8FF11A-D9F5-4D65-BF30-A03FE9AEA808.jpeg (1868.51 KB, 4032x3024 - viewed 11 times.)
Logged
Cor
Cape Town
Member
*
Online Online

Posts: 644


I am probably fishing......


« Reply #1 on: January 12, 2019, 07:07:44 AM »

Those parts both come off there respective shafts.

The small washer F47-0101 probably won't come off further because the drive shaft F73-3602 is slightly damaged or has a small burr.  Push it back and just use a fine flat file very carefully over the flat sides to remove any high points on the brass drive shaft. Shocked

The bearing does not seem to have corrosion on it, so try some penetrating oil overnight.

I don't have precisely the same reel but they are all very much the same.
Logged

Cornelis
Mrc70
Member
*
Offline Offline

Posts: 29


« Reply #2 on: January 12, 2019, 07:32:02 AM »

Thanks, Cor!  That is exactly what I suspected.
Logged
Jigtosser
Member
*
Online Online

Posts: 78


« Reply #3 on: January 12, 2019, 02:26:03 PM »

What Cor said...  Cheesy
They are good reels !!!
Dan
Logged
Mrc70
Member
*
Offline Offline

Posts: 29


« Reply #4 on: January 13, 2019, 08:52:15 AM »

Well, I was able to remove the small washer (thanks, Cor). However, I cannot get that bearing off the spool shaft!  I have tried penetrating oil, using two screw drivers to walk it out, channel locks.. it won’t budge!
Logged
Donnyboat
donnyboat
Photo Group
Member
**
Online Online

Posts: 966


« Reply #5 on: January 13, 2019, 09:50:02 AM »

your on to it, more penatrating oil, & patients, it should give the way your going about it, good luck, please keep us informed,cheers Don.
Logged

Don, or donnyboat
Cor
Cape Town
Member
*
Online Online

Posts: 644


I am probably fishing......


« Reply #6 on: January 13, 2019, 10:18:03 AM »

I blew up the picture and it looks like there is corrosion on the bearing, so its probably shot in any event.   More penetrating oil.

If the bearing is already ruined, hold it in a vice .......

Keep trying, perhaps tap it inward (towards te spool) with light hammer using a small socket or something that will fit around the shaft.   Gently does it, it will release, don't bend the shaft on the other side of the spool!
Heat may also do it.

Just keep trying but very gently and carefully.    The "bigger the problem the bigger the hammer" does not apply here Undecided
« Last Edit: January 13, 2019, 10:28:10 AM by Cor » Logged

Cornelis
Mrc70
Member
*
Offline Offline

Posts: 29


« Reply #7 on: January 13, 2019, 01:10:16 PM »

Got it!!  I kept using the penetrating oil..  Gave it one more try..  and used two screw drivers to pry/walk the bearing off the shaft..  Thanks to all who replied!  And yes, there was a lot of rust on that bearing..
« Last Edit: January 13, 2019, 01:11:02 PM by Mrc70 » Logged
Donnyboat
donnyboat
Photo Group
Member
**
Online Online

Posts: 966


« Reply #8 on: January 13, 2019, 04:24:16 PM »

through the bearing, the rest should cleen up okay, all we need now, is a photo of the fish you catch with it. cheers Don.
Logged

Don, or donnyboat
Mrc70
Member
*
Offline Offline

Posts: 29


« Reply #9 on: January 13, 2019, 07:29:56 PM »

Thank you!
Logged
alantani
admin
Administrator
Member
*****
Online Online

Posts: 16983



« Reply #10 on: January 13, 2019, 10:56:50 PM »

this works for bearings also.


Logged

send me an email at alantani@yahoo.com for questions!
Mrc70
Member
*
Offline Offline

Posts: 29


« Reply #11 on: January 14, 2019, 11:40:42 AM »

Thanks, Alan.  That's exactly what I did...after a lot of penetrating oil. 

Logged
Mrc70
Member
*
Offline Offline

Posts: 29


« Reply #12 on: January 15, 2019, 02:19:08 PM »

I am wondering where I can buy a couple of bearings (key # 14 and key #20)for my x40HA at a reasonable price?  I am also looking for a clamp kit if anyone has any suggestions.. it doesn't have to be a Daiwa clamp..

Thanks again!  
« Last Edit: January 15, 2019, 02:27:49 PM by Mrc70 » Logged
Cor
Cape Town
Member
*
Online Online

Posts: 644


I am probably fishing......


« Reply #13 on: January 15, 2019, 04:08:44 PM »

I probably have a clamp that you may have for free, but the shipping cost from here will be too much.
Logged

Cornelis
doradoben
Member
*
Online Online

Posts: 337


« Reply #14 on: January 15, 2019, 11:57:38 PM »

I don't know where you are located but you might try Daiwa in California. I've purchased parts from them in the past and they were reasonable and helpful.

http://www.daiwa.com/us/about/index.html

http://www.daiwa.com/us/service/manuals/index.html
Logged
Pages: [1] 2   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Simple Audio Video Embedder
Valid XHTML 1.0! Valid CSS!
Page created in 0.215 seconds with 18 queries.