alan tani @ alantani.com fishing reel repair rebuild tutorial Daiwa Slt tournament 50w 2 peed drag washers...
Reel Repair by Alan Tani
December 06, 2019, 09:38:57 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Search Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: Daiwa Slt tournament 50w 2 peed drag washers...  (Read 625 times)
0 Members and 1 Guest are viewing this topic.
Noahg727
Member
*
Offline Offline

Posts: 64



« on: April 08, 2019, 03:00:44 PM »

So for those of you who donít know, the Daiwa Slt 50wís drag washers are terrible. At first glance they look like carbon fiber but I believe they are actually some crappy Kevlar or something. Either way I was wondering how I can replace these drag washers? I want to completely sand them off and glue a pair of carbon fiber ones on their place. Is this possible? Iv never done anything like this. Let me know what yíall think.

Noah


* 4F1129C6-1D6C-4A00-9231-FECD1E45E346.jpeg (1871.87 KB, 4032x3024 - viewed 29 times.)
Logged
alantani
admin
Administrator
Member
*****
Online Online

Posts: 17852



« Reply #1 on: April 08, 2019, 06:45:14 PM »

Well, you'd have to chisel off the original material,  clean up the aluminum,  then glue on some carbon fiber. The problem is the adhesive. Most have used epoxy.  Loctite Depend 330 is the best, but it is prohibitively expensive.  That's why I gave up on it. The few times I've glued in some Avet drags, I just used epoxy.
Logged

send me an email at alantani@yahoo.com for questions!
Noahg727
Member
*
Offline Offline

Posts: 64



« Reply #2 on: April 09, 2019, 01:59:12 AM »

Thanks Alan!

Where do you think the best place to get the new carbon fiber drag washers is? And do you think doing this is worth it? The washers are fine as it is but just make me uneasy knowing what theyíre made of.

Noah
Logged
nelz
Member
*
Offline Offline

Posts: 896



« Reply #3 on: April 09, 2019, 09:17:27 AM »

Noah, have you tried cleaning them and then using a little drag grease? They look to be in good condition.

Btw, isn't Kevlar supposed to be a premium material and quite expensive? That's not to say it works well for drags, I have no idea about that.
Logged
alantani
admin
Administrator
Member
*****
Online Online

Posts: 17852



« Reply #4 on: April 09, 2019, 02:06:42 PM »

i tried drag grease on these and it made them worse.  dry is probably best.   Undecided
Logged

send me an email at alantani@yahoo.com for questions!
Noahg727
Member
*
Offline Offline

Posts: 64



« Reply #5 on: April 09, 2019, 04:31:51 PM »

I wanted to soak them in mineral spirits and then grease em up again, but I was concerned it would possibly destroy them. Iím telling you, you touch them and they start flaking pieces off. I was so confused when I first saw it. Gently wiped off the grease on there and reapplied some fresh Calís. Havenít really had a chance to use it but hopefully it didnít make it worse! Itís a shame...these reels are so pretty. I got a brand new one for a friend and it looks the part. Just a little underwhelming performance wise from what Iíve seen. 🤷‍♂️
Logged
nelz
Member
*
Offline Offline

Posts: 896



« Reply #6 on: April 09, 2019, 05:47:17 PM »

Ah-ha, well if they're flaking apart it's surely time to replace them, whatever material they are. You can always buy a sheet of carbon fiber and cut your own if the right size disk or close to it isn't available.

They sure are good looking reels, I've always admired them.
Logged
Noahg727
Member
*
Offline Offline

Posts: 64



« Reply #7 on: April 10, 2019, 12:50:21 PM »

Where could I find a carbon fiber sheet and how whatís the best method to cut them?
Logged
redsetta
Moderator
Member
****
Offline Offline

Posts: 2746


Auckland, New Zealand


« Reply #8 on: April 10, 2019, 01:45:23 PM »

Dawn at SmoothDrag is great to deal with:
Also, Sal uses this seller:
Large-diametre drag washers like this can be cut with scissors, X-acto knives etc.
(Just don't forget the old maxim 'Measure twice, cut once'!  Wink Grin)
Smooth off the edges with sandpaper or a dremel, but be mindful of the CF dust as it can be a real irritant on the skin.
Hope that helps.
Keep us up on progress.
Cheers, Justin
Logged

Fortitudine vincimus - By endurance we conquer
handi2
Sensei
Member
***
Offline Offline

Posts: 3424


OCD Reel Service and Repair


« Reply #9 on: April 10, 2019, 02:04:21 PM »

I have done this on other reels. I used 3M adhesive spray but  I donít remember the product number. No problems at all. If you soak them in mineral spirits you can remove the drag material with a razor blade. Get the razor blade in the edge of the drag washer and plate.

I did this when the customer didnt have much money for a new one.

Keith
Logged

OCD Reel Service & Repair
Gulf Breeze, FL
Noahg727
Member
*
Offline Offline

Posts: 64



« Reply #10 on: April 12, 2019, 08:25:50 AM »

Thanks guys, appreciate all the info! Iíll let yah know how it goes.
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Simple Audio Video Embedder
Valid XHTML 1.0! Valid CSS!
Page created in 0.238 seconds with 18 queries.