alan tani @ alantani.com fishing reel repair rebuild tutorial Tiburon frame on S332-5 - gears donít seem to mesh as well ?
Reel Repair by Alan Tani
September 15, 2019, 04:38:15 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Search Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: Tiburon frame on S332-5 - gears donít seem to mesh as well ?  (Read 314 times)
0 Members and 1 Guest are viewing this topic.
Fishead
Member
*
Offline Offline

Posts: 109


« on: September 01, 2019, 01:01:30 PM »

Just put the tiburon frame on the S332-5 and it feels like the gears are grinding or not meshing like they were before the new frame. Did I miss something?
Logged

If you're not fishing,you're wishing you were!!
Newell Nut
Firearms Group
Member
**
Online Online

Posts: 2406



« Reply #1 on: September 01, 2019, 02:36:14 PM »

You missed something but no clue what.

Dwight
Logged
PacRat
Member
*
Online Online

Posts: 465



« Reply #2 on: September 01, 2019, 03:22:39 PM »

1) Adjust your spool side-to-side. I'm assuming you have adjustable bearings on both sides. Do this first.
2) If you did any work in your head-plate; check the drive-train. Like Dwight said...something is out of place.
Good luck
-Mike
Logged
Swami805
Member
*
Online Online

Posts: 2631


« Reply #3 on: September 01, 2019, 03:27:38 PM »

 If adjusting the bearing cap ( I think you only have 1 ?) doesn't help,Try adding or deleting shims to move spool shaft a little.
 Also try taking it apart and turn the frame so it's facing the other direction, sounds dumb but worth a try.
I'm assuming it worked fine with the stock frame
Logged
Bryan Young
Ultimate Upgrades Drags
Administrator
Member
*****
Online Online

Posts: 10219


The Reel Whisperer


« Reply #4 on: September 02, 2019, 07:03:33 AM »

Itís possible that the stock frame was slightly out of alignment, and now that it is squared, the gears will be noisy since they are now at a 90 deg angle. That would be my first guess given everything else being equal.
Logged

Cheesy I talk with every part I send out and each reel I repair so that they perform at the top of their game. Cheesy
Newell Nut
Firearms Group
Member
**
Online Online

Posts: 2406



« Reply #5 on: September 02, 2019, 09:03:47 AM »

Every tib frame that I have installed on a 300 series has holes a couple thousandths out from the SS newell rings. I use a mini round file to adjust the holes in the SS rings to match the tib frame. Other than that make sure you back off the left side bearing a couple turns before reassembly. Should be no issue after that. Readjust spool space and should spin like a top.
Logged
Fishead
Member
*
Offline Offline

Posts: 109


« Reply #6 on: September 03, 2019, 05:43:04 AM »

This reel only has left side adjustable bearing cap. I have messed with it from really tight to a lot of play with no change in gears. I did not take handle side-late apart before putting it on the frame. I did have to take a round file to the handle side plate inner ring to open up the threaded holes a little. Swapping the frame around sounds like the next thing to try. Must be something with the S series. I just put a Tib frame on my red 332 and it works fine.
« Last Edit: September 03, 2019, 05:46:40 AM by Fishead » Logged

If you're not fishing,you're wishing you were!!
Newell Nut
Firearms Group
Member
**
Online Online

Posts: 2406



« Reply #7 on: September 03, 2019, 04:49:20 PM »

The S series has nothing to do with it. I have installed on Ss and Cs both with long bolts and no issue at all other than tweaking the ring holes. You will figure it out and it will be something very simple.
Dwight
Logged
Fishead
Member
*
Offline Offline

Posts: 109


« Reply #8 on: September 04, 2019, 02:13:11 PM »

Iím thinking itís the gears are shot. I swapped the handle side plate from 2 of my 332ís and those worked just fine on that reel. Probably the easiest solution is new gears.
Logged

If you're not fishing,you're wishing you were!!
Newell Nut
Firearms Group
Member
**
Online Online

Posts: 2406



« Reply #9 on: September 04, 2019, 02:58:48 PM »

Pro Challenger had a bunch of gears. Not sure if they all got sold or not.
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Simple Audio Video Embedder
Valid XHTML 1.0! Valid CSS!
Page created in 0.196 seconds with 19 queries.