alan tani @ alantani.com fishing reel repair rebuild tutorial Parts for Progear CS 501
Reel Repair by Alan Tani
October 22, 2020, 12:08:21 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Search Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: Parts for Progear CS 501  (Read 182 times)
0 Members and 2 Guests are viewing this topic.
SeaMonster
Member
*
Offline Offline

Posts: 5


« on: October 16, 2020, 11:44:11 AM »

Hello,  I hopeful someone can help me find a handle retaining nut and the screw that locks it in place for a CS-501.  I lost it years ago when trying to find a handle upgrade.  Any help would be greatly appreciated.  Thanks-  Mike
Logged
alantani
admin
Administrator
Member
*****
Offline Offline

Posts: 18810



« Reply #1 on: October 16, 2020, 12:41:36 PM »

mike, i might have a set.  can you get calipers and measure the largest diameter of the drive shaft?
Logged

send me an email at alantani@yahoo.com for questions!
SeaMonster
Member
*
Offline Offline

Posts: 5


« Reply #2 on: October 16, 2020, 12:54:26 PM »

Sure,  should the reel be disassembled to take the measurement?
Logged
SeaMonster
Member
*
Offline Offline

Posts: 5


« Reply #3 on: October 16, 2020, 01:09:30 PM »

If it helps the size is 5/16x24tpi
Logged
alantani
admin
Administrator
Member
*****
Offline Offline

Posts: 18810



« Reply #4 on: October 16, 2020, 03:11:35 PM »

All i have is this.


* 20201016_161057.jpg (2764.33 KB, 4032x3024 - viewed 0 times.)
Logged

send me an email at alantani@yahoo.com for questions!
Wompus Cat
Member
*
Offline Offline

Posts: 34


« Reply #5 on: October 16, 2020, 03:57:23 PM »

in case one needs to know the decimal eq of 5/16 =0.3125 or approx 8mm
Logged
SeaMonster
Member
*
Offline Offline

Posts: 5


« Reply #6 on: October 16, 2020, 06:00:21 PM »

Thanks guys,  the battery in my caliper is dead.  I’ll pick one up tomorrow and see what it is and get back to you.

Thanks again

Mike
Logged
Wompus Cat
Member
*
Offline Offline

Posts: 34


« Reply #7 on: October 17, 2020, 03:20:10 AM »

On another note the Nut Mr. Tani is illustrating is closer to 1/4 inch or 6.35  mm
Logged
Tiddlerbasher
Photo Group
Member
**
Online Online

Posts: 3017



« Reply #8 on: October 17, 2020, 04:09:42 AM »

Remember - if you measure the inside of a nut it will be smaller than measuring the outside of the shaft even if they are both tha correct size Wink
The 'minor diameter of a 5/16 nut is approx 0.265" the 'major' diameter is approx 0.3125"
From Alan's measurement his nut is probably 5/16"
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Simple Audio Video Embedder
Valid XHTML 1.0! Valid CSS!
Page created in 0.174 seconds with 17 queries.