alan tani @ alantani.com fishing reel repair rebuild tutorial Daiwa Sealine 600H Rebuild and Upgrade
Reel Repair by Alan Tani
August 23, 2019, 08:42:52 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Search Login Register  
Pages: 1 [2] 3 4   Go Down
  Print  
Author Topic: Daiwa Sealine 600H Rebuild and Upgrade  (Read 34489 times)
0 Members and 4 Guests are viewing this topic.
floating doc
Firearms Group
Member
**
Offline Offline

Posts: 876


« Reply #15 on: August 04, 2012, 01:49:31 PM »

Oh, best of luck! Standing by for a report!
Logged

Central Florida
Joel.B
Firearms Group
Member
**
Offline Offline

Posts: 333


« Reply #16 on: August 20, 2013, 09:44:39 AM »

Well I know what I'll be doing to the 600h I just received.   This is great thread
Logged
madday
Member
*
Offline Offline

Posts: 73


« Reply #17 on: February 27, 2014, 11:26:41 PM »

this is maybe sound stupid,
just to confirm, is that on the picture is daiwa's original metal washer can be used to make 5+1 stack?

i own 4 of this reel, and this kind of tuning is really great.... Cheesy
Logged
Bryan Young
Ultimate Upgrades Drags
Administrator
Member
*****
Online Online

Posts: 10188


The Reel Whisperer


« Reply #18 on: February 28, 2014, 12:25:07 AM »

The posting shows the use of Penn 114H's metal drag washers.  I wasn't going to say anything because I don't line spouting my own horn...but I do have a concern about using Penn's 114H metal drag washers, particularly the keyed metal washers.  I have attached my photo of the comparison.

The last photo will show that the Penn 114H metal drag washer has a gap of about 2 mm.  Under higher drag pressures, they can and will grove into the gear sleeve, and you may experience a set drag because the drag washer will groove into the gear sleeve or even damage the gear sleeve. 

For this reason, I have created a drag kit of thinner stainless steel material where the keyed washer is from 0.25 to 0.5 mm larger than the gear sleeve itself to provide more contact area which will result in less chances of grooving into the gear sleeve, and therefore achieve greater drag numbers will less likelihood of damage to the gear sleeve.

By the way, Daiwa's stock metal washers are THICK and you cannot use them completely to create a 5 carbon fiber stack system in the main gear.


* Daiwa 600H comparision to 114H.jpg (134.86 KB, 1153x1525 - viewed 368 times.)
Logged

Cheesy I talk with every part I send out and each reel I repair so that they perform at the top of their game. Cheesy
Shark Hunter
Moderator
Member
****
Offline Offline

Posts: 11097


The Rogue of the Seven Seas!


« Reply #19 on: February 28, 2014, 01:02:46 AM »

Nice post Bryan! I like the little text boxes. Nice touch. Wink
Logged

Life is Good!
madday
Member
*
Offline Offline

Posts: 73


« Reply #20 on: February 28, 2014, 03:21:18 PM »

X2.... nice post bryan....
thanks for the enlightment....  Wink
Logged
day0ne
Member
*
Online Online

Posts: 754


« Reply #21 on: February 28, 2014, 10:38:11 PM »

The posting shows the use of Penn 114H's metal drag washers.  I wasn't going to say anything because I don't line spouting my own horn...but I do have a concern about using Penn's 114H metal drag washers, particularly the keyed metal washers.  I have attached my photo of the comparison.

The last photo will show that the Penn 114H metal drag washer has a gap of about 2 mm.  Under higher drag pressures, they can and will grove into the gear sleeve, and you may experience a set drag because the drag washer will groove into the gear sleeve or even damage the gear sleeve. 

For this reason, I have created a drag kit of thinner stainless steel material where the keyed washer is from 0.25 to 0.5 mm larger than the gear sleeve itself to provide more contact area which will result in less chances of grooving into the gear sleeve, and therefore achieve greater drag numbers will less likelihood of damage to the gear sleeve.

By the way, Daiwa's stock metal washers are THICK and you cannot use them completely to create a 5 carbon fiber stack system in the main gear.

I mentioned the Penn washers because I had trouble finding the Daiwa washers, however, I found them and the reel was assembled with the Daiwa metal washers. Yes you can use them to create a 5+1 drag stack.  They work just fine. The only Penn washer was the HT-100 under the main gear. I also mentioned that the Penn washers had a slightly oversize hole and smaller ears.
Logged

David


"Lately it occurs to me: What a long, strange trip it's been." - R. Hunter
madday
Member
*
Offline Offline

Posts: 73


« Reply #22 on: March 01, 2014, 01:09:09 AM »

I mentioned the Penn washers because I had trouble finding the Daiwa washers, however, I found them and the reel was assembled with the Daiwa metal washers. Yes you can use them to create a 5+1 drag stack.  They work just fine. The only Penn washer was the HT-100 under the main gear. I also mentioned that the Penn washers had a slightly oversize hole and smaller ears.

thanks for the insight...
so using addition 2 daiwa metal washers (keyed and eared) is no problem right? just use thinner carbon washer to compensate... then its fine.....  Huh?
Logged
Bryan Young
Ultimate Upgrades Drags
Administrator
Member
*****
Online Online

Posts: 10188


The Reel Whisperer


« Reply #23 on: March 01, 2014, 08:35:34 AM »

I mentioned the Penn washers because I had trouble finding the Daiwa washers, however, I found them and the reel was assembled with the Daiwa metal washers. Yes you can use them to create a 5+1 drag stack.  They work just fine. The only Penn washer was the HT-100 under the main gear. I also mentioned that the Penn washers had a slightly oversize hole and smaller ears.

thanks for the insight...
so using addition 2 daiwa metal washers (keyed and eared) is no problem right? just use thinner carbon washer to compensate... then its fine.....  Huh?
that is possible but I nave not tried it.
Logged

Cheesy I talk with every part I send out and each reel I repair so that they perform at the top of their game. Cheesy
maine guide
Member
*
Offline Offline

Posts: 30


« Reply #24 on: May 04, 2014, 05:36:40 AM »

I am considering a 600h now that I just acquired two 900h's. Alan, do you have an upgraded drag kit for the 600h like you do for the 900h?  Thanks.
Logged
Bryan Young
Ultimate Upgrades Drags
Administrator
Member
*****
Online Online

Posts: 10188


The Reel Whisperer


« Reply #25 on: May 04, 2014, 07:30:44 AM »

I am currently out and am still awaiting the parts from the cutter.  I'm a small customer so I have to wait.
Logged

Cheesy I talk with every part I send out and each reel I repair so that they perform at the top of their game. Cheesy
maine guide
Member
*
Offline Offline

Posts: 30


« Reply #26 on: May 04, 2014, 11:01:54 AM »

Thanks Bryan. Any eta?
Logged
jonnou
Member
*
Offline Offline

Posts: 387



« Reply #27 on: July 12, 2014, 01:14:11 AM »

Just stripped mine Im sure I can 5+1 it with factory washers
Logged
Marquesas14
Member
*
Offline Offline

Posts: 8


« Reply #28 on: June 25, 2015, 02:22:18 PM »

I've enjoyed this thread very much, it's helped me rebuild my dad's old 600h I found in the attic. I was hoping someone here could help me however. The only thing missing from the reel being perfect, are the badges/decals. I've called Daiwa and they told me no dice. I was hoping one of you fine gentlemen would know of another source?
Logged
Rancanfish
Member
*
Offline Offline

Posts: 1724


« Reply #29 on: June 25, 2015, 06:09:19 PM »

I'm no help M-14, but fish that bad boy.  Your Dad or the fish don't care how pretty it is.

I have a missing badge on one of mine but I try to ignore it.

Good luck, I hope you find it though.
Logged

Can't sleep, clowns will eat me.
Pages: 1 [2] 3 4   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Simple Audio Video Embedder
Valid XHTML 1.0! Valid CSS!
Page created in 0.212 seconds with 17 queries.