Stainless Newell Gears

bigcatpat · November 19, 2013, 05:17:13 AM

Thanks Sal.I'll just wait for Alans gears.I'm not good at waiting though.

Wildman · April 20, 2014, 02:53:50 AM

I'm just a bit late

to this party, but are Newell 3.6:1 (or similar) gears available for the 200 series?

Bryan Young · April 20, 2014, 05:34:13 AM

No they're not. Only 5:1 gears are being produced. You might be able to use Penn 500/501 gears in a pinch. I haven't tried them on the Newells yet to see if any modifications are necessary.

bluefish69 · April 20, 2014, 04:56:12 PM

I believe it's the Penn 506 gears are the correct ones because they are 5-1. Only problem is the main gear is Brass, I'm not sure of the pinion gear though.

Mike

Newell Nut · April 20, 2014, 05:08:25 PM

Maybe not being produced at the moment but I have P235 3.6 in my desk. I am hoping Alan Chui solves all the penn gear issues and gets started on the Newell gears next. 3.6 gears are at the top of my list

bluefish69 · April 20, 2014, 05:34:14 PM

NN

You got my last set of 3.6-1 gears

Newell Nut · April 20, 2014, 06:42:15 PM

Being used on every trip in my 440.

bluefish69 · April 20, 2014, 07:12:13 PM

NN

You could send me a Fillet

Mike

Newell Nut · April 20, 2014, 07:47:30 PM

I would if FedEx was not so expensive. Hope your boat gets out soon. With the current forecast Tuesday is iffy for us and Thur looks promising. All that I can do is just lift weights to prepare for the next trip when it happens.

Wildman · April 20, 2014, 09:45:44 PM

Bummer. Sounds like a common issue. Has anyone actually used Penn Main Gears and Pinions to lower the Newell gear ratios?

The old Penns were 3.3:1 if I remember correctly, 500 series were 4.25 maybe?...and I have one or two 140s/500s/501s/etc. I could pull from...

maxpowers · April 22, 2014, 12:34:21 AM

Quote from: Wildman on April 20, 2014, 09:45:44 PM
Bummer. Sounds like a common issue. Has anyone actually used Penn Main Gears and Pinions to lower the Newell gear ratios?

The old Penns were 3.3:1 if I remember correctly, 500 series were 4.25 maybe?...and I have one or two 140s/500s/501s/etc. I could pull from...

Yes it can be done. I just swapped out some 5:1 p338-F gears for penn 4:1 steel gears. Didn't seem to have any issue.

Oahutaco · July 21, 2014, 03:11:04 AM

Do you still have any more sets for sell?

GKFISH · February 17, 2015, 07:28:00 PM

I install Penn gears all the time for Newell customers...Never had an issue.

Penn part #'s
5-500 main gear
13-500 pinion gear

4.0:1 ratio

GKFISH

Bryan Young · February 17, 2015, 07:48:43 PM

I believe you can also use Penn's 505/506 gears as well.

speedwagon2 · February 17, 2015, 08:54:19 PM

Dawn,
Shure could use a set of 4.6 gears for a 500 series, and a set of 3.2s for the 600 series
Thanks, Speedwagon2