Here's all of Shimano's Schematics, current and discontinued. Just go through the scroll down menu until you find the reel you're looking for:
http://fish.shimano.com/publish/content/global_fish/en/us/index/customer_service0/Reel_Schematics.html
Hope this helps,
Dom
AHhh its back up & working...
Sun & Mon (4-24/25-11) the Torium 30 (all toriums from what I saw) were not working, had to order part Mon AM and had to go on Dougs word, I was blind!!!
Alan, I am looking for a diagram of a Shimano Triton Speedmaster II. Looking thru the Shimano list I do not find it.
I have a almost mint SMII. When taken out of gear the spool binds. But not all the time. This may be my doing. I recently serviced this reel, Checked, and greased the drag, Etc. I may have lost a washer, or reversed something??? Anyway a diagram or help would be appreciated.
Thanks,
Dave S.
P.S. I now have 6 Okumas, and am waiting for a 8.
Is this the one?
http://schematics.planetseafishing.com/downloads/shimano/multiplier/triton-series/triton-speedmaster-ii(91-45).pdf
Yes, thanks.
I have a speedmaster II that needs part # 0236,the star for the drag.Anyone know if it is available anywhere?.Or if the star from any other reel may fit,I don't have access to any of the small trinidads but think maybe the smaller reels star may fit since I believe it to be the same gear ratio.At this point,I dont care if the star is gold,as long as I can use it.I tried Mikes but never heard back from them.
I am looking for the schematics for a Stradic 2000 FH. I looked on the site that was given above by Broadway but did not see it. Can anyone help?
Thanks
Jim
2500FH nearest I can get to it. Are you in the UK?
http://schematics.planetseafishing.com/downloads/shimano/fixed-spool/stradic-series/stradic-st2500fh(2003).pdf
No sir, I am in the U.S. (Winter Garden, Florida)
Quote from: Irish Jigger on September 28, 2011, 08:37:52 PM
2500FH nearest I can get to it. Are you in the UK?
http://schematics.planetseafishing.com/downloads/shimano/fixed-spool/stradic-series/stradic-st2500fh(2003).pdf
My bad Sir, It is a 2500 that I am looking for. Thanks for your help
Quote from: gasman1 on September 29, 2011, 06:46:36 PM
No sir, I am in the U.S. (Winter Garden, Florida)
Lucky man having all that great fishing over there.
anyone got a full schematics for a trynos2 lever dragc
an only find one half done
pete
here you go pete;
http://fish.shimano.com/publish/content/global_fish/en/us/index/customer_service0/Reel_Schematics.html
just click your model...
Quote from: Mel B on January 03, 2013, 12:06:13 PM
here you go pete;
http://fish.shimano.com/publish/content/global_fish/en/us/index/customer_service0/Reel_Schematics.html
just click your model...
i look there but mine is not a 2 speed
pete
here you go for a single speed;
http://fish.shimano-eu.com/publish/content/global_fish/uk/nl/index/customer_service0/Reel_Schematics.html
select multipliers then tyrnos then your model..hope this is it ???
thanks mel
have u got one that tell me how to service one and put it back together
pete
no don't have but you may want to take a look at this again.
http://alantani.com/index.php?topic=1583.0
yes mel
i saw that one but its not finished
ty for your time
pete
don't mention it, that's what we are here for,tight lines!
what a wonderful site -- SOOOO happy I found it!!! many thanks to the creator & contributors!
is there a source for older JDM schematics (organized in ENGLISH!!!)... or, a member who understands Japanese enough to help me out? I have a few beloved JDM's that I use very sparingly, only because I'm reluctant to service them without the blueprints:
Scorpion Metanium XT (L/H): I upgraded it externally with a longer 4-BB Chronarch-B handle, but fear digging in the innards (not much practice with Baitcasters :-[ )... could I get by with Chronarch-SF & Chronarch-B schematics?
Biomaster LS 2500S rear-drag: I'm very comfortable with most pre-2005 US Shimano spinners; I can handle rear drags & worm gears just fine, individually; but I never worked a reel that has BOTH... could I get by with UK Biomaster 2500RA/3000SRA schematics?
TwinPower XT 4000/5000 schematics would be nice - if handy, but I'm sure it's just a Sustain FA with better handle, so I'm OK.
I only need schematics for the JDM models in bold -- I have everything else & all the reels are working perfectly, so there's no rush. Thanks, in advance, for the help (or, even, commiseration ::))
Roman
scorpion metanium try the core version, twinpower try the stella version... ???
Hello, this is my first post on this site. This is a great site, you guys have a wealth of knowledge.
I have been looking for drawings for a Curado Bantam 200. There are no other numbers on it that I can find. When I download one for a 200, I always end up getting a 200B or a 100. My question would be is the 200b the bantam and is it the same as a 100?
I am going to install carbontex drag. I had a local reel repairman work on it for me, he installed a new drag and nothing changed. When pulling drag out by hand it jerks badly. From most of the drawings that I've seen all the drag components are the same but I would like to know for sure which drawing is correct as I may need to order other parts later.
Thanks 😁🐟
This would be the one you should use.
Can't seem to find schematics for an old discontinued reel
Triton Mark IV S
http://www.nutterrodandreel.com/ProductData.cfm?id=Shimano
http://www.nutterrodandreel.com/ProductData.cfm?id=Shimano (http://www.nutterrodandreel.com/ProductData.cfm?id=Shimano)
Just came across this!
I have purchased a Japan Shimano Scorpion Metanium XT and have looked for a schematic for this reel. I have seen the Shimano Japan site but I can't read Japanese. I have read that the Chronach 100 b is similar to this reel but was really looking fior a correct schematic. Can anyone help please!
Does anybody know where I can find a schematics for a Shimano Ocea Jigger EV 2500 PG? Can't find any on the Shimano website.
404 Not Found.
Looks like the original Shimano link has been changed...
You tried http://fish.shimano.com/
I'm very frustrated that Shimano stopped offering schematics from discontinued reels in their European site. I'm trying to find the ones for my Shimano Ultegra 10000XT (Made In Japan model). Goggled it but i still can't find it anywhere.
Is there anyone can help?
Quote from: zerofish on March 08, 2015, 09:26:29 PM
I'm very frustrated that Shimano stopped offering schematics from discontinued reels in their European site. I'm trying to find the ones for my Shimano Ultegra 10000XT (Made In Japan model). Goggled it but i still can't find it anywhere.
Is there anyone can help?
EUROPEAN UNION:
http://fish.shimano-eu.com/content/eu/en/Home/customer-service/exploded-views-reels.html (http://fish.shimano-eu.com/content/eu/en/Home/customer-service/exploded-views-reels.html)USA:
http://fish.shimano.com/content/sac-fish/en/home/customer-service/reel-schematics.html (http://fish.shimano.com/content/sac-fish/en/home/customer-service/reel-schematics.html)
Thank you for the reply but there are no discontinued reels on the European site...
Still can't find the Shimano Ultegra 10000XT schematics...
Ok here goes.
Just bought a Shimano Bantam 1000 Tournament State side today.
Does anybody know or have a schematic for this reel or can scan one up from their own copy and PDF me a copy?
It's a 32+ year old reel that I have some huge appreciation for and finally after a lot of llooking I found one in great condition bit without box and papers...
Any help would be greatly appreciated!
Andrew
Quote from: zerofish on March 30, 2015, 06:06:52 AM
Thank you for the reply but there are no discontinued reels on the European site...
Still can't find the Shimano Ultegra 10000XT schematics...
Hmm . . . I'm working on it with a couple of UK forums, fingers crossed.
Perhaps this one might be almost identical ?
http://www.mikesreelrepair.com/schematics/albums/shimano/Shimano_Ultegra_UL10000XSC_Schematic.pdf (http://www.mikesreelrepair.com/schematics/albums/shimano/Shimano_Ultegra_UL10000XSC_Schematic.pdf)
Hi Slazmo,
hope one of the schematics is correct
Hi Wooli.
The closest is the Bantam 1000P. However mine is the Bantam 1000 Tournament.
Unsure what may be the difference but they look the same bar the handles?
Thanks anyhow.
Still on the hunt Shimano Bantam 1000 Tournament (Circa 1981 to 1983)
Thanks.
Andrew
Quote from: zerofish on March 08, 2015, 09:26:29 PM
I'm very frustrated that Shimano stopped offering schematics from discontinued reels in their European site. I'm trying to find the ones for my Shimano Ultegra 10000XT (Made In Japan model). Goggled it but i still can't find it anywhere.
Is there anyone can help?
Zerofish,
I received a schematic for the SHIMANO ULTEGRA XT10000, directly from the company that does Shimano's service in the UK . . . I sure hope that this is the one you're looking for - LOL !
It's ATTACHED as a PDF below :
Tight Lines !
Plus, a couple of JPG's . . .
Tight Lines !
Can't thank you enough ez2cdave!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
You saved me!!!
Quote from: zerofish on April 02, 2015, 10:11:40 AM
Can't thank you enough ez2cdave!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
You saved me!!!
Thanking me enough, is going to be VERY EXPENSIVE, I'm afraid . . . In "just compensation", you must swear to ALWAYS do your best to HELP OTHERS !!!
Deal ???
Tight Lines !!!
DEAL
Hi. Does anybody have the schematics for Shimano Sahara 1000 GTE, or know how to get hold of it? It is approximately 10-15 years old, and a rear drag model.
Or if anyone knows the dimension of the ball bearings in it?
Thanks in advance.
Martin
Quote from: glowgrrr on August 24, 2015, 08:59:23 PM
Hi. Does anybody have the schematics for Shimano Sahara 1000 GTE, or know how to get hold of it? It is approximately 10-15 years old, and a rear drag model.
Or if anyone knows the dimension of the ball bearings in it?
Thanks in advance.
Martin
Don't quote me on this but just about every smaller Shimano spinner I have worked on uses 7x14x5, 7x13x4, and 7x11x3. This doesn't help you much but it will give you and idea what to look for when you take it apart.
Hi again,
I have done some digging during day time and found out some more:
handi2, you are right on the dimensions. It is using 2 x 7x13x4mm (Shimano part #RD0930 ), and 1 x 7x14x5mm (Shimano part #RD0026)
MeL B, that link lead to a front drag reel, but i was able to find a similar 1000 class reel i can look at on that site.
Thank you both for your help!
Martin
Hi, I'm looking for Shimano Biomaster 8000Xt model 1995 schematics. does anyone have any pdf copy? Thanks :)
TwinPowerXT is the JDM version of '97 SustainFA (virtually identical -- diff. handle & color)
your BiomasterXT is the JDM version of a Stradic...
probably FE('97), but also check FD ('94,95,96)...
use 4000-size, in case 6000/8000-size was not offered in US that year:
https://www.reelschematic.com/reel-schematics/shimano-reel-schematics/shimano-stradic-schematics/#gsc.tab=0 (https://www.reelschematic.com/reel-schematics/shimano-reel-schematics/shimano-stradic-schematics/#gsc.tab=0)
here is the list of shimano reel schematics (1550 entries total): http://www.shimanopromotions.com.au/schematics/
Now, that's handy.
-steve
Quote from: sparidae on January 29, 2020, 07:35:33 PM
here is the list of shimano reel schematics (1550 entries total): http://www.shimanopromotions.com.au/schematics/
Many thanks !
I have added your link to this thread . . .
https://alantani.com/index.php?topic=14458.45 (https://alantani.com/index.php?topic=14458.45)Tight Lines !
Hi,
I am glad that I found this forum!
I am looking for a schematic of the above mentioned reel.
When I was looking at the links here I could not find it.
Maybe someone can help me out.
Best Regards from Germany
Ernst
yeah, no luck either. :-\
which reel?
Shimano Twinpower 1000
need photos, or exact model, or year of production
should be a Sustain from same year & nearly identical
maybe different handle & color scheme -- so, some different part #'s
(true for older models, not sure about newer)
search both, "Twinpower" & "Twin Power"
The model is SC541. Thank you Philaroman
You probablly checked
this site (https://www.reelschematic.com/reel-schematics/shimano-reel-schematics/shimano-twin-power-schematics/#gsc.tab=0)
Already but there are only a Few of the Twin Power Schematics posted .....Maybe one of those is close to what you have .
Quote from: Weinbauer on May 11, 2021, 12:16:20 AM
The model is SC541. Thank you Philaroman
that doesn't look like any Shimano model#... from where are you reading it?
can you figure out what year? not sure how/if Sustain/TwinPower diverged after move to Malaysia,
but if your TP is more than 20 years old, then it's same as Japan-made Sustain
look at schematics for SA1000F, SA1000FA, SA1000FB, SA1000FD
you can find SA1000F here:
https://www.reelschematic.com/wp-content/uploads/schematics/Shimano/Sustain/SHIMANO%20SUSTAIN%20SA1000F%2893-22%29.pdf (https://www.reelschematic.com/wp-content/uploads/schematics/Shimano/Sustain/SHIMANO%20SUSTAIN%20SA1000F%2893-22%29.pdf)
https://www.reelschematic.com/wp-content/uploads/schematics/Shimano/Sustain/SHIMANO%20SUSTAIN%20SA1000F%20PARTS%2893-23%29.pdf (https://www.reelschematic.com/wp-content/uploads/schematics/Shimano/Sustain/SHIMANO%20SUSTAIN%20SA1000F%20PARTS%2893-23%29.pdf)
...but, reelschematic has some confusion w/ FB & FD, so get SA1000FA, SA1000FB, SA1000FD here:
http://www.shimanopromotions.com.au/schematics/ (http://www.shimanopromotions.com.au/schematics/)
if you have a newer TwinPower <20-y-o, type "TP1000F" in Model & they all pop up
(bad search engine; difficult to navigate site; type in Model, only -- EXACTLY!)
that looks like 1993 original TP/SustainF -- screw-in handle; SuperStopper A/R (not instant); bearing under spool like Stella
if you have SuperStopper II instant ARB, then it's 1997 TwinPowerXT/SustainFA (through-gear handle, no bearing under spool)
you can use Sustain schematics -- only paint & handles are different