bearing sizes by reel - a running list

[alantani]

jimmer had a great idea of having a running list of the different sizes of bearings for all the reels.  and he's right.  if everyone chips in, this could be a real time saver for everyone.  the list will go by manufacturer (penn, shimano, etc.), then by model name (say, curado), then by model number (100D, 300E) and then by bearing location with the dimensions (left spool 4x11x4).  just post your bearing dimensions here and the moderators will add it to the list.  jimmer, thanks for the great idea!

[Dominick]

Wow! This thread didn't go anywhere .  I searched for this thread because I need the size for spool bearings for a Penn International 50VSW does anyone have the answer?  If not I will take the reel apart and measure them and post the size here. 
Dominick

[Irish Jigger]

Here you go,  Daiwa Saltiga 30.
4x11x4mm #6-1 reqd
8x14x4mm #11-1 reqd
3x8x4mm #23-1  reqd
8x14x4mm #60-1 reqd
5x8x2.5mm #71-2 reqd

#Ref Schematics.

http://www.daiwa.com/PartsDiagram/PartsDiagram/SA15-30.pdf

[Irish Jigger]

 And another,
Penn 113H, Spool bearings, 0.1250 x 0.3750 x 0.1562 inch-2 reqd.

[rjones]

Penn squidder 140 uses 2 each .125" X .500" X .1719"

[D impala95]

Shimano Calcutta CTE250DC

Pinion                8x12x3.50mm
Worm gear         5x8x2.50mm
Spool                 3x10x4mm (2)
Drive shaft inner 5x8x2.50mm
Drive shaft outer 8x12x3.50mm
Grip                   4x7x2.50mm (4)

[Bryan Young]

Shimano Trinidad TN30
Spool Bearing (right) - 6 X 12 X 4 mm
Spool Bearing (left) - 4 X 11 X 4 mm

[Irish Jigger]

Penn 330GTI & 320GTI.
Bridge bb, 8x16x5 mm.
LS Spool bb,4x11x4 mm./
                 

[Irish Jigger]

Shimano Trinidad TN16.
LHS Side Plate 4x11x4mm.
RHS Spool 6x12x4mm.(no part# shown on schematics.)
LH end Drive Shaft 5x9x3mm.
RH end Drive Shaft 10x15x4mm.

[D impala95]

Pflueger President WLPL

Side cover spool bearing            3x10x4
Mid shaft spool bearing              5x11x4
Spool bearing under tension cap 3x8x4
Drive shaft                                5x9x3
Worm shaft                               4x7x2.5
Grip/handle (4)                         5x8x2.50

[Jimmer]

Shimano Charter special  1) 12x17x5   2) 5x11x4  1) 7x17x5

[ebnash]

The following are only spool bearings...

Avet MXL                .185 X .5 X .195
                            .185 X .311 X .125

Avet JX                   .185 X .685 X .250
                            .185 X .375 X .125

Avet HX                   6 X 19 X 6mm
                             6 X 12 X 4mm

Daiwa Saltist LD35H    7 X 17 X 5mm
                             6 X 13 X 5mm

[ebnash]

Avet HX Raptor - 2012 Production(Keep in mind that this may not cover your reel as I have seen other dimension for HX Raptor in earlier productions)

Left Spool – 6 X 12 X 4
Right Spool – 6 X 12 X 4
Left Pressure Plate – 6 X 19 X 6
Right pressure Plate - 6 X 12 X 4
Inner Drive Shaft - .375 X .625 X .156
Outer Drive Shaft - .375 X .625 X .156
Right Plate – 6 X 19 X 6

[ebnash]

Abu 6501-C3 Older Model
                                      Qty
Spool Bearings 4 X 10 X 4       2
Pinion Bearing  8 X 13 X 4       1

[reel bob]

Penn 345 GTi Gear Stud - Part # 55-80ST - .500 x .875 x .2188 or 1/2 x 7/8 x 7/32

Heres the size...Problem I have is where to purchase this size bearing other than Boca or Scotts. There has to be cheaper prices than what they want...Any Help?