New Dragwasher Sizing List

Bryan Young · June 09, 2012, 12:27:31 AM

Hot off the electronic presses.

New Carbontex Drag sizing chart.
Washer Number OD X ID X Thickness, mm(In.)
1 16 (0.613) X 8.25 (0.325) X 0.5 / 0.76 / 1 (0.02 / 0.03 / 0.04)
2 16.8 (0.66) X 4.3 (0.169) X 1 (0.04)
3 16.95 (0.666) X 5.95 (0.235) X 1 (0.04)
4 17.15 (0.675) X 9.35 (0.368) X 0.5 (0.025)
5 17.8 (0.7) X 10.35 (0.407) X 0.76 (0.03)
6 18.25 (0.72) X 8.35 (0.33) X 1 (0.04)
7 18.75 (0.735) X 10.9 (0.43) X 1 (0.04)
8 19.5 (0.765) X 4.2 (0.165) X 1 (0.04)
9 20.5 (0.805) X 10.85 (0.43) X 0.76 (0.03)
10 20.5 (0.81) X 8.1 (0.32) X 0.5 (0.02)
11 20.65 (0.81) X 8.9 (0.35) X 1 (0.04)
12 20.7 (0.815) X 13.15 (0.518) X 0.76 (0.03)
13 21.28 (0.84) X 5.18 (0.205) X 1 (0.04)
14 21.5 (0.85) X 8.1 (0.32) X 0.76 / 1 (0.03 / 0.04)
15 21.6 (0.85) X 10.6 (0.415) X 0.76 (0.03)
16 22.6 (0.89) X 12.7 (0.5) X 1 (0.04)
17 22.95 (0.905) X 8.3 (0.325) X 1 (0.04)
18 22.98 (0.095) X 8.15 (0.32) X 0.5 / 0.76 (0.020 / 0.03)
19 23.9 (0.94) X 11.3 (0.445) X 1 (0.04)
20 24.15 (0.95) X 14.5 (0.572) X 1 (0.04)
21 24.55 (0.965) X 10.6 (0.415) X 0.5 / 0.76 (0.020 / 0.03)
22 24.6 (0.97) X 14.5 (0.57) X 0.76 (0.03)
23 24.63 (0.969) X 5 (0.198) X 1 (0.04)
24 24.65 (0.97) X 19.3 (0.76) X 0.76 (0.03)
25 25.3 (0.995) X 17.05 (0.675) X 1 (0.04)
26 25.4 (1) X 8.4 (0.33) X 0.76 / 1 (0.03 / 0.04)
27 25.5 (1) X 8.65 (0.34) X 0.5 (0.02)
28 25.8 (1.015) X 18.7 (0.735) X 1 (0.04)
29 25.8 (1.015) X 10.75 (0.425) X 2 (0.08)
30 25.95 (1.02) X 19.25 (0.76) X 1 (0.04)
31 26 (1.022) X 12 (0.475) X 0.76 (0.03)
32 26.45 (1.044) X 8.35 (0.329) X 1 (0.04)
33 26.5 (1.045) X 13 (0.515) X 0.76 (0.03)
34 26.55 (1.045) X 15.65 (0.615) X 0.76 (0.03)
35 26.75 (1.05) X 17 (0.67) X 1 (0.04)
36 26.8 (1.055) X 12.75 (0.5) X 0.5 (0.02)
37 26.8 (1.055) X 9.6 (0.375) X 0.5 (0.02)
38 26.85 (1.055) X 12.65 (0.5) X 1 (0.04)
39 27.05 (1.065) X 8.3 (0.325) X 0.5 / 1 (0.020 / 0.04)
40 27.1 (1.066) X 13.85 (0.545) X 1 / 1.2 (0.04 / 0.047)
41 27.95 (1.1) X 15.65 (0.615) X 0.76 (0.03)
42 28 (1.1) X 10.9 (0.43) X 0.76 (0.03)
43 28.35 (1.115) X 18.9 (0.745) X 1 (0.04)
44 28.6 (1.125) X 10.9 (0.429) X 0.76 / 1 (0.03 / 0.04)
45 28.65 (1.13) X 21.05 (0.83) X 1 (0.04)
46 29 (1.14) X 8.6 (0.34) X 0.76 (0.03)
47 30.95 (1.22) X 21.6 (0.85) X 0.76 (0.03)
48 31 (1.22) X 8.9 (0.35) X 1 (0.04)
49 31.15 (1.225) X 17 (0.668) X 1 (0.04)
50 32.35 (1.275) X 8.25 (0.325) X 0.65 / 0.76 (0.025 / 0.03)
51 32.5 (1.28) X 24.55 (0.965) X 1 (0.04)
52 32.65 (1.285) X 17.1 (0.673) X 0.76 (0.03)
53 33.5 (1.32) X 18.05 (0.71) X 1 (0.04)
54 33.8 (1.33) X 9.5 (0.373) X 1 (0.04)
55 34.65 (1.365) X 19.45 (0.765) X 0.76 (0.03)
56 34.92 (1.376) X 20.26 (0.807) X 0.96 (0.037)
57 35.07 (1.376) X 15.5 (0.611) X 1 (0.04)
58 35.5 (1.4) X 25.75 (1.105) X 1 (0.04)
59 35.6 (1.4) X 8.7 (0.34) X 0.5 (0.02)
60 38.15 (1.5) X 14 (0.55) X 1 (0.04)
61 38.5 (1.515) X 24.1 (0.948) X 1 (0.04)
62 40.45 (1.59) X 21.05 (0.83) X 0.76 (0.03)
63 40.45 (1.59) X 13 (0.51) X 0.76 (0.03)
64 41.05 (1.62) X 16.35 (0.645) X 0.76 (0.03)
65 41.05 (1.62) X 12.55 (0.495) X 0.76 (0.03)
66 41.05 (1.62) X 10.1 (0.4) X 0.76 (0.03)
67 43 (1.695) X 16.25 (0.64) X 0.76 (0.03)
68 43 (1.695) X 12.15 (0.48) X 0.76 (0.03)
69 43 (1.695) X 10.35 (0.405) X 0.76 (0.03)
70 49.15 (1.935) X 20.35 (0.8 ) X 1.16 (0.045)
71 55 (2.165) X 20.05 (0.79) X 1.16 (0.045)

LTM · June 09, 2012, 05:19:26 AM

Thanx Bryan,

I plan on getting as much data into several spread sheets that I am working on and this is much appreciated.

Leo

Nessie Hunter · June 09, 2012, 08:02:28 PM

Very good, thank you lots....

aaronb · June 15, 2012, 01:35:52 PM

On your list you just have numbers by them. Do I just go to the smooth drags carbontex drag list and count down to number 47 for example and see what that washer is listed for? Thanks.

Dr. Jekyll - AKA MeL B · June 15, 2012, 01:44:34 PM

actually you look for the size CF washer you need and the corresponding number to the left is the part number. hope this is what you meant.

Dawn · June 15, 2012, 03:57:27 PM

Aaron
The numbers are the size chart do not correspond to anything else

Just tried to keep it simple for ordering.
If you want to know what reel a particular washer belongs to just email and ask me.

Dawn

Dr. Jekyll - AKA MeL B · June 15, 2012, 08:43:59 PM

Quote from: Dawn on June 15, 2012, 03:57:27 PM
The numbers are the size chart do not correspond to anything else

Dawn

Dawn, i thought that was the purpose of the part numbering system to make life easier. for example if i wanted OD 21.28 mm ID 5.18 and 1 mm thickness i will order washer number 13, am i wrong?

thanks!

Dawn · June 16, 2012, 04:20:40 PM

Mel you are right. I mis-understood what you meant.

fishnazzi · June 21, 2012, 11:38:40 PM

OK here comes a dumb guy question...........I have a pile of Bass pro shop bait-casters......I know that they are made by several reel manufactures...can I get you bass pro #'s for proper CF washers?

David Bentley · June 22, 2012, 02:24:15 AM

fishnazzi, remember there are no dumb questions, only dumb answers.

fishnazzi · June 22, 2012, 03:30:42 AM

dumb guy......thats me at times.........The drag washers on a couple of my reels are hammered. So I'm afraid trying measure the thickness of a hammered unit won't work.......and of course they are made by someone.......(the reels)......not sure about how to get the right sizes or if they are available........

Bryan Young · June 22, 2012, 06:29:30 AM

Good question....but I don't have a good answer. Thickness is a game of chance. i just worked on a little shimano bass reel, and switched drags 3 times until I got the right thickness...how do I know? It was based on the star and how much drag I got based on the position of the star. If you get too much drag at the top, the washers are too thick. If bottoming out, too thin. Then I just try to find something in between...but I have a collection of washers to choose from and mix and match.

fishnazzi · June 22, 2012, 01:01:58 PM

sounds like it might be easier to send the reels in............

Dawn · June 22, 2012, 03:39:55 PM

You can send me the old washers if that's easier.

Dawn

fishnazzi · June 23, 2012, 02:44:36 AM

That might work for me Dawn.....Thank You. It is summer season right now and work hours are long. But......in the fall........It is big fish time here. I will have to work at getting you some old ones(out of the reels) and in the mail.

New Dragwasher Sizing List

David Bentley