alan tani @ alantani.com fishing reel repair rebuild tutorial Penn 113h 4/0 build Questions
Reel Repair by Alan Tani
September 20, 2019, 10:17:58 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Search Login Register  
Pages: 1 [2] 3 4   Go Down
  Print  
Author Topic: Penn 113h 4/0 build Questions  (Read 2761 times)
0 Members and 1 Guest are viewing this topic.
RowdyW
Firearms Group
Member
**
Online Online

Posts: 2433



« Reply #15 on: October 06, 2018, 07:32:30 AM »

The nylon bushing goes on the eccentric in the right plate. The o ring goes on the left bearing cap. The nylon cap goes on the eccentric lever to keep it from leaving marks on the edge of the right plate. You can pack the bearings with gease or oil them. Grease will last much longer. Snap ring pliers will not work as the rings do not have holes  for the pliers. I put a dab of grease on the e clip, put a finger on top of it & push it in with a small screwdriver while under my finger to keep it from going to never neverland. When you put the tongue on intall it with the rounded edges up & sharper edges down.         Rudy
« Last Edit: October 06, 2018, 07:44:52 AM by RowdyW » Logged
Swami805
Member
*
Online Online

Posts: 2635


« Reply #16 on: October 06, 2018, 07:43:21 AM »

No grease in the bearings if you want good free spool, the lube of choose id tsi321 for the best free spool. Very light oil if you don't have that.
You shouldn't need any special tool for the clicker assembly, the C-clip just pops on. Be careful though,they can go flying off to a different dimension. I can push them on with my finger.
Post some pictures when you're done
Logged
wideopenoutdoors
Member
*
Offline Offline

Posts: 33



« Reply #17 on: October 06, 2018, 09:42:27 AM »

Thanks guys, i have never seen an eccentric with a cap before!
Logged

"your not on a fishing show, reel it in!"
RowdyW
Firearms Group
Member
**
Online Online

Posts: 2433



« Reply #18 on: October 06, 2018, 09:51:17 AM »

It's to prevent the aluminum plate from wearing which is softer then the brass eccentric. By the way glue the little nylon cap on to the eccentric lever because they fall off in use.
Logged
wideopenoutdoors
Member
*
Offline Offline

Posts: 33



« Reply #19 on: October 06, 2018, 01:34:59 PM »

Starting  the tear down and re-assemble of the first reel. Is there anything in particular i should look at? im just replacing the drag set with a 5 stack and re-using everything else- the upgrades will come later. this reel started out as a dark maroon post frame clicker style 113h.


* IMG_20181006_172259067.jpg (4762.71 KB, 3006x5344 - viewed 54 times.)
Logged

"your not on a fishing show, reel it in!"
wideopenoutdoors
Member
*
Offline Offline

Posts: 33



« Reply #20 on: October 06, 2018, 03:11:19 PM »

ok so i hit a snag, my red side plates two posts that held the eccentric spring, the new side plate doesnt have anything, am i missing something?


* IMG_20181006_190517921.jpg (4096.82 KB, 5344x3006 - viewed 51 times.)
Logged

"your not on a fishing show, reel it in!"
Cortez_Conversions
Sensei
Member
***
Online Online

Posts: 1038



WWW
« Reply #21 on: October 06, 2018, 03:42:05 PM »

The tag end of the spring goes into the detent just below the spring in you last pic. Iím ata distillery event now, but Iíll check back in this evening.
Cheers!
Logged

Visit: cortezconversions.com
wideopenoutdoors
Member
*
Offline Offline

Posts: 33



« Reply #22 on: October 06, 2018, 03:56:25 PM »

thanks, im currently struggling to remove a drag washer corroded to the inside of the main gear 
Logged

"your not on a fishing show, reel it in!"
mhc
Sensei
Member
***
Online Online

Posts: 939


« Reply #23 on: October 06, 2018, 04:38:03 PM »

Here's a photo of what Tom has explained.

Mike


* DSCF3788.JPG (1107.09 KB, 2592x1944 - viewed 51 times.)
Logged

It can't be too difficult - a lot of people do it.
wideopenoutdoors
Member
*
Offline Offline

Posts: 33



« Reply #24 on: October 06, 2018, 04:46:03 PM »

im working on that part now, slowly realizing how wore out most of my reels and their components are :/
thanks for the picture, its worth a thousand words
Logged

"your not on a fishing show, reel it in!"
Dominick
Administrator
Member
*****
Online Online

Posts: 7627


San Mateo, California


« Reply #25 on: October 06, 2018, 04:55:12 PM »

Hey Wide Open you are new to this site.  Now tell us whether it has reached or exceeded your expectations.  BTW welcome.  As you can see all you have to do is ask and the answers keep coming.   Cool  Dominick
Logged

Leave the gun.  Take the cannolis.

 Give a man a fish and he will eat for a day. Teach a man to fish and he will sit in a boat all day drinking beer.
wideopenoutdoors
Member
*
Offline Offline

Posts: 33



« Reply #26 on: October 06, 2018, 05:14:23 PM »

Dominick- the site has exceeded my expectations.
Logged

"your not on a fishing show, reel it in!"
Donnyboat
donnyboat
Photo Group
Member
**
Online Online

Posts: 1307


« Reply #27 on: October 06, 2018, 06:56:12 PM »

Ah Dom, they call it ohana, OHANA, Nice timing Mike with your photo, Wideopen, your doing okay, we learn all the time, first thing I say when I get out of bed every morning ,yes I am going to learn something new today, good luck cheers Don.
Logged

Don, or donnyboat
wideopenoutdoors
Member
*
Offline Offline

Posts: 33



« Reply #28 on: October 07, 2018, 05:36:44 AM »

update, after screaming at the anti-reverse dog until late in the evening i called it quits. this morning i got it first try, go figure. almost have the first reel completely assembled. Its been over two years since i took these reels apart and it showed. luckily i was about to remember how i did the anti reverse dog- too bad i couldn't remember last night.
Logged

"your not on a fishing show, reel it in!"
wideopenoutdoors
Member
*
Offline Offline

Posts: 33



« Reply #29 on: October 07, 2018, 11:10:56 AM »

finished one, opened the second and found it has a stainless pinion gear.
Logged

"your not on a fishing show, reel it in!"
Pages: 1 [2] 3 4   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Simple Audio Video Embedder
Valid XHTML 1.0! Valid CSS!
Page created in 0.211 seconds with 17 queries.